Bench Grinders
| MachineInfoBox Bench Grinders | |
|---|---|
| |
| Synonyms: | bench top grinders, grinding wheels; DE: Schleifmaschinen |
| Material: | metal (not aluminum) |
| Access Requirements: | Bench Grinder Introduction |
| Tutors: | Lukas Pakue Johannes Luzian Utis Sebastian |
| Similar (More or Less): | disc grinder, files, sandpaper |
Safety
As the bench grinder is not only a power tool but one with openly accessible spinning parts, precautions need to be made. Have a tutor show the machine to you before touching it!
- never wear gloves and/or scarves, roll up long sleeves and tie back long hair so nothing gets caught
- always wear personal protection, especially safety goggles and if necessary some ear defenders and a dust mask
Usage
- after plugging the grinder in, turn it on and wait until it reaches its final speed
- if you hear any rattling or other funny noises turn it off immediately and check whether something is loose or whether tiny parts are inside of the casing
- grind whatever you want to grind by holding it against the stone wheel; make sure the piece is supported either by the little table in front of the wheel or some other structure
- do not force your workpiece onto the wheel as that will produce a lot of heat; cooling your piece from time to time is always a good idea
Sharpening
- approach the spinning wheel slowly so your workpiece doesn't catch on it!
- when sharpening hardened steel make sure to keep the blade cool, otherwise previous hardening may be undone!
- it's a good idea to press the blade firmly against the support to keep a consistent blade alignment
- check the squareness of the blade often to be able to make corrections
- keep in mind that the grinder itself is only for roughing out the blade geometry, for a truly sharp blade you definitely need to work with some wetstones afterwards
Brüder Mannesmann M1225-125
| MachineInfoBox Brüder Mannesmann M1225-125 | |
|---|---|
| |
| Synonyms: | bench top grinder, grinding wheel; DE: Doppelschleifer, Schleifbock, Trockenschleifmaschine |
| Material: | metal (not aluminum) |
| Access Requirements: | Bench Grinder Introduction |
| Manual: | Völkner.de |
| Tutors: | Lukas Pakue Johannes Luzian Utis Sebastian |
| Similar (More or Less): | disc grinder, files, sandpaper |
[[Has caption::power sharpening tool| ]]
This bench grinder from 1996 is used but still in decent condition; the wheels run true and quietly. The grinder is equipped with two different stone wheels with different grits (35 & 60); one for heavy-duty and quick material removal, one for a finer and more precise material removal that will leave a way nicer surface finish.
Maintenance
The wheels need to be "dressed" from time to time in order to produce nice straight edges and maintain stability. Apparently, it's possible to do that with nothing more than a few spring washers on a piece of threaded rod![1] We should try this before spending time and money on a more sophisticated tool.
Changing Wheels
After installing a new grinding wheel, set up a safety perimeter (let's say everyone leaves the room) and let the grinder run for five minutes. Only if that went well, without suspicious noises or visible signs of problems, should the grinder be used again.
Upgrade Ideas
For really sharp knives, we could turn an MDF wheel on the wood lathe and use that as the final "grit".
Triton TWSS10
| MachineInfoBox Triton TWSS10 | |
|---|---|
| |
| Synonyms: | wet grinder, whetstone sharpener, dual-purpose wet grinder/stropping wheel; DE: Nassschleifmaschine |
| Material: | metal (not aluminum) |
| Access Requirements: | Bench Grinder Introduction |
| Manual: | Instruction Manual Explosion Diagram Product Sheet |
| Tutors: | Lukas Pakue Johannes Luzian Utis Sebastian |
| Similar (More or Less): | disc grinder, files, sandpaper |
[[Has caption::power sharpening tool| ]]
The Triton TWSS10 provides a stone for wet grinding and a leather stropping wheel. Please ensure you always empty the water and loosen the torque screw when you are done!
This grinder is slow moving and intended for the final sharpening passes, not gor quick material removal. It has a 220 grit "diamond wheel" (with a water bath) and a leather honing wheel. It may be nice to add a swiveling base under it so you don't need to pick up the machine to switch directions!
There are quite a few accessories available from the manufacturer. You can find them in the manual (page 8) as well as on the product page.
We should document individual accessories as we get (or 3D print) them.
Straight Edge Jig
We have a straight edge jig for flat irons like bevel edge chisels or plane blades.
