Uploads by Lukas

From CoMakingSpace Wiki

This special page shows all uploaded files.

File list
First pagePrevious pageNext pageLast page
Date Name Thumbnail Size Description Versions
14:26, 30 December 2020 Schalltür4.JPG (file) 666 KB die Aussparung für das Einsteckschloss ''kann'' man zwar im verschraubten Zustand fräsen - denkt man aber rechtzeitig daran, kann die Latte einfach auf dem Frästisch bearbeitet werden! Project:Schallschutztüren 1
14:24, 30 December 2020 Schalltür3.JPG (file) 526 KB vor dem Verschrauben sollte das Einsteckschloss eingepasst werden - für den richtigen Sitz im Rahmen musste eine Vertiefung in die kleinere Platte gefräst werden Project:Schallschutztüren 1
14:21, 30 December 2020 Schalltür2.JPG (file) 488 KB die beiden massiven Platten wurden mit einem leichten Rahmen als Mittelschicht verschraubt - mit einem Zirkel können solche Bohrungen ohne Rechnen gleichmäßig angeordnet werden Project:Schallschutztüren 1
12:31, 30 December 2020 Schalltür1.JPG (file) 422 KB sobald eine Tür auf den Rahmen zugeschnitten war, wurden die Bänder eingedreht um den Sitz möglichst früh testen und ggf. verbessern zu können Project:Schallschutztüren 1
12:18, 30 December 2020 Schalltür0.JPG (file) 375 KB "Baustelle" für unsere Schallschutztüren kurz vor Fertigstellung 1
11:23, 30 December 2020 Fishcage3D.png (file) 114 KB final snap ring design in Tinkercad - super fancy, I know! Project:Fish Cages 1
11:16, 30 December 2020 Fishcage7.JPG (file) 371 KB the bottom ends of the cages were wet sanded until they were even enough to form a tight seal with the mesh & snap ring Project:Fish Cages 1
11:10, 30 December 2020 Fishcage6.JPG (file) 342 KB the floaters were held underwater for a couple of days after washing with ethanol to get rid of the laser stench Project:Fish Cages 1
11:02, 30 December 2020 Fishcage5.JPG (file) 316 KB all the parts after the "machine work" at the Space: tubes, floaters and snap rings Project:Fish Cages 1
10:57, 30 December 2020 Fishcage4.JPG (file) 463 KB laser cutting the floaters out of XPS Project:Fish Cages 1
10:49, 30 December 2020 Fishcage3.JPG (file) 295 KB a 3D printed snap ring that was just a bit too large - note the cracks forming in the acrylic glass tube Project:Fish Cages 1
10:44, 30 December 2020 Fishcage2.JPG (file) 354 KB The initial plan was to glue the mesh directly onto the cut face of the acrylic tube, but I did not know the material (probably a non-gluable plastic) and therefore failed quickly. Project:Fish Cages 1
10:34, 30 December 2020 Fishcage0.JPG (file) 4.05 MB a floating "fish cage" with some tiny zebrafish larvae inside Project:Fish Cages 1
10:25, 30 December 2020 Bandsaw sled guides.JPG (file) 311 KB some 3D printed T-slot guides were screwed into the bandsaw sled at just the right places for nice tracking on the machine table 1
10:18, 30 December 2020 Bandsaw sled without clamps.JPG.jpg (file) 424 KB   1
10:12, 30 December 2020 Bandsaw sled.JPG (file) 463 KB clamps can be used with a bandsaw sled for maximum safety, e.g. when there is a high danger of round stock rolling around 1
11:38, 20 December 2020 Jointer push blocks.jpg (file) 390 KB both of these push block designs may be used with the jointer, depending on workpiece size 1
18:54, 8 December 2020 Lasercut 5.3 order.png (file) 10 KB the easy way to define output order in LaserCut 5.3 - select the "layer", then use the Up and Down buttons 1
03:08, 5 December 2020 Makita router with stolen dust adapter.jpg (file) 334 KB The scroll saw has a shop vac adapter we don't need, and the Makita router needed one - tada! 1
13:25, 2 December 2020 Karel - bed leg.jpg (file) 347 KB When the legs on your bed break, just make super solid, new ones! Photo by Karel Category:Repair 1
03:37, 29 October 2020 Abrichte falsch bekleidet.JPG (file) 223 KB At the Jointer-Planer you MUST NOT (red) wear jewellery, including watches and rings, or loose long clothing. 1
02:59, 23 October 2020 Planer - angled infeed.JPG (file) 435 KB Feeding boards through a planer/bottom of a jointer-planer at a slight angle may help to avoid "snipe" ''(Hobelschläge)'' 1
02:22, 23 October 2020 Jointer - fingers together.JPG (file) 470 KB When moving a workpiece over the jointer, your fingers should always remain close together and far from the blades. 1
02:10, 23 October 2020 Abrichte - Hilfsanschlag.svg (file) 3.79 MB Benutzung des Hilfsanschlags beim Abrichten schmaler Werkstücke ''Use of the auxiliary fence when jointing narrow workpieces'' ---- created with Inkscape 1
18:27, 20 August 2020 Chainsaw mill - first board.jpg (file) 270 KB The first full board cut with {{£}}'s chainsaw. Project:Chainsaw Mill 1
16:32, 1 August 2020 Makita 3612BR in router table.png (file) 1.16 MB the machine control elements of the Makita 3612BR you'll need for operation in the router table 1
16:05, 1 August 2020 Router table - starting pin.png (file) 711 KB When working fenceless with a guide-bearing bit on the router table, a starting pin needs to be used for a safe first contact with your workpiece. It helps you make sure your workpiece stays in front of the router bit! 1
09:51, 1 August 2020 Makita 3612BR - collet sleeve.JPG (file) 1.39 MB a collet sleeve (silver) reduces the Makita 3612BR collet diameter from 12 to 8 mm for common hobbyist router bits 1
16:51, 28 July 2020 Makita 3612BR.JPG (file) 604 KB type plate on our Makita 3612BR router 1
00:08, 28 July 2020 Lapping stone.JPG (file) 324 KB a self-made lapping stone on a table 1
20:08, 4 May 2020 GT-7910A.jpg (file) 123 KB the EasyHome GT-7910A ultrasonic cleaner in operation 1
02:48, 30 April 2020 Carpenter's mallet - Lukas2.JPG (file) 239 KB Project:Mallets nearly completed carpenter's mallet from self-dried timber 1
02:06, 30 April 2020 Carpenter's mallet - Lukas.JPG (file) 177 KB Project:Mallets carpenter's mallet made from self-dried timber (before finishing) 1
01:57, 30 April 2020 Applying finish.JPG (file) 365 KB finishing a wooden mallet handle 1
01:17, 30 April 2020 Curved cherry.JPG (file) 313 KB Project:Drying Timber curved cherry log pretty soon after cutting the young bent tree 1
01:13, 30 April 2020 Old cherry.JPG (file) 339 KB Project:Drying Timber freshly cleaned up and split cherry branch from an old tree 1
00:46, 30 April 2020 Drying freshly cut lumber.JPG (file) 245 KB Project:Drying Timber a small log of cherry hand-cut into (more or less straight) boards for drying 1
00:29, 30 April 2020 Japanese skiving knife demo.JPG (file) 339 KB how to hold a Japanese skiving knife to cut leather 1
00:22, 30 April 2020 10 Million Dollar Stick demo.JPG (file) 458 KB how to use a 10 Million Dollar Stick to hold small stock on the chop saw 1
22:49, 29 April 2020 Router jig with jigsaw.JPG (file) 673 KB Project:Schallschutztüren some router jigs can also be used with a jigsaw, but at least the corners won't turn out nearly as nice 1
22:46, 29 April 2020 Jigsaw idea - custom-fit shelf.JPG (file) 278 KB another use for jigsaws: cutting a corner out of a custom-fit shelf 1
20:23, 29 April 2020 Small fire.JPG (file) 301 KB fire is hot! 1
20:21, 29 April 2020 Paste wax 2x.JPG (file) 396 KB two jars of self-mixed paste wax 1
20:10, 29 April 2020 Sewing awl.JPG (file) 346 KB a sewing awl being used to stitch two pieces of leather together 1
19:55, 29 April 2020 Shrink fit example.JPG (file) 490 KB shrink-fitting: after this scooter part was heated in a drying oven and the bearings were cooled down with freeze spray, the parts slid together easily and were solidly connected once everything was back at the same temperature 1
00:49, 23 April 2020 Japanese leather knife.JPG (file) 458 KB a Japanese leather knife 1
00:05, 23 April 2020 Daubers.JPG (file) 524 KB two wool daubers for dye applications in leatherworking 1
23:52, 22 April 2020 Leather burnishers.JPG (file) 483 KB two leather burnishers 1
23:03, 22 April 2020 Skivers.JPG (file) 500 KB two skivers used for leatherworking 1
21:48, 15 April 2020 Auger bit shaft - square.png (file) 56 KB illustration of a square, tapered auger bit shaft screenshot; quickly modeled in Tinkercad 1
First pagePrevious pageNext pageLast page