Jointer-Planer: Difference between revisions

From CoMakingSpace Wiki

(→‎Jointing: how to glue off-square joints)
m (→‎Planing: forgotten image caption)
Line 52: Line 52:


== Planing ==
== Planing ==
[[File:planer - angled infeed.JPG|thumb|200px]]  
[[File:planer - angled infeed.JPG|thumb|200px|angled infeed as one way to mitigate snipe]]  
If you flip the top of the machine back, you're able to feed a workpiece ''under'' the knives to plane its top surface. Thereby you can obtain a board with parallel faces and dial in its thickness exactly as you want. Make sure you fully [https://www.popularwoodworking.com/article/understanding-grain-direction/ understand grain direction] or you'll easily get tearout!
If you flip the top of the machine back, you're able to feed a workpiece ''under'' the knives to plane its top surface. Thereby you can obtain a board with parallel faces and dial in its thickness exactly as you want. Make sure you fully [https://www.popularwoodworking.com/article/understanding-grain-direction/ understand grain direction] or you'll easily get tearout!



Revision as of 22:11, 9 December 2020

MachineInfoBox

Hammer A3-31

Hammer A3-31.jpg
Synonyms: planer-thicknesser, power jointer, thickness planer;
DE: Abricht- und Dickenhobelmaschine, "Abrichte", "Dickte"
Material: naturally structured wood
(not more engineered than glued laminated timber!)
Used with: push block with lip, dust extractor
Access Requirements: Jointer-Planer IntroductionSome use of "" in your query was not closed by a matching "".
Manual: felder-gruppe.at (DE), (EN)
Tutors: Lukas
Pakue
Sebastian
LoewensteinSome use of "" in your query was not closed by a matching "".
Similar (More or Less): jointer plane, planer

A jointer is used for straightening the narrow sides of wooden boards which is necessary for panel glue-ups and some kinds of joinery. It basically consists of a flat surface with a slightly protruding cutting drum at the center.

We chose to get a combination jointer/planer to save valuable space: thanks to the second flat surface under this cutting drum, you can also thickness boards with this machine! You can therefore buy rough-sawn wood and dimension it at the CoMakingSpace.


This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!

Task comment Status
Name the tool: - done
Take a picture - Done
Find the manual as PDF felder-gruppe.at (DE), (EN) done
Documentation this page, status: in commissioning pending
Print QR-Code use the wikicrawler pending
Introduction Jointer-Planer Introduction Done
Security Check to be done or witnessed by a manager done
Test to be done or witnessed by a manager Done
tool's name, owner and approx. value provide to Patrick for inventorization Done
Last step: make it available physically and in the wiki - then delete this template pending


Jointing

when moving a workpiece over the jointer, your fingers should always remain close together and far from the blades

Jointing (using the top table of the machine) creates flat, perpendicular surfaces. Flawless edges are especially important for glue-ups, e.g. to make your own glued laminated timber panels!

You should check the fence for squareness against the table, e.g. with a square or inclinometer. Advanced users may also try to joint at other angles than 90°.

A square fence is not absolutely required for a good glue-up joint: if you can't improve squareness (or want to play it safe either way), try varying the orientation of each board's edges as you joint them. If all your "left" edges are off-square in one direction and all the "right" ones are the opposite, you will still get a perfectly matching, but not square, joint (video).

Planing

angled infeed as one way to mitigate snipe

If you flip the top of the machine back, you're able to feed a workpiece under the knives to plane its top surface. Thereby you can obtain a board with parallel faces and dial in its thickness exactly as you want. Make sure you fully understand grain direction or you'll easily get tearout!

Feeding boards through at a slight angle may help to avoid "snipe" (Hobelschläge) but you should be prepared to cut off unsightly ends afterwards - i.e., plane oversized boards and cut them to length as the next step.

Accessories

Dust Evacuation

The planer should only be used in tandem with a suitable dust evacuation system. The intended machine for this purpose is the Felder AF 14, that should be in close proximity to the planer. The system should be hooked up through the automated switch box (switched output) mounted on the metal frame, that should also be connected to the planer (trigger output). Once the planer is started the vacuum system will turn on after 3 seconds and turn off once the planer is off for 8 seconds. Make sure to set the switch on the vacuum motor to '1' (ON) before starting!

Alternatives