Chop Saw: Difference between revisions
NitramLegov (talk | contribs) (added Elektra Bekum KS 210 HM Plus) |
m (→Elektra Bekum KS 210 HM Plus: naming typo) |
||
| Line 41: | Line 41: | ||
* There is a clamping point on the right side of the blade, but when you actually put the clamp in there the motor will hit it. Could be fixed by adding a compatible hole (or simply another clamp) about 10 cm further to the right...very smart design -.- | * There is a clamping point on the right side of the blade, but when you actually put the clamp in there the motor will hit it. Could be fixed by adding a compatible hole (or simply another clamp) about 10 cm further to the right...very smart design -.- | ||
=Elektra | =Elektra Beckum KS 210 HM Plus= | ||
{{ToolInfoBox | {{ToolInfoBox | ||
|tool name=Elektra | |tool name=Elektra Beckum KS 210 HM Plus | ||
|image= | |image= | ||
|synonyms= | |synonyms=compound miter saw;<br>DE: Kappsäge, Kapp- und<br>Gehrungssäge | ||
|type=power tool/[[:Category:Saws|saw]] | |type=power tool/[[:Category:Saws|saw]] | ||
|access= | |access=[[Chop Saw Introduction|chop saw introduction]] | ||
|location=Commissioning shelf | |location=Commissioning shelf | ||
|material=[[wood]] | |material=[[wood]] | ||
| Line 56: | Line 56: | ||
}} | }} | ||
{{NL}} brought in an alternative chop saw, which needs to be commissioned before it can be used. | {{NL}} brought in an alternative chop saw, which needs to be commissioned before it can be used. | ||
If we can get it set up on the same height as the other one and with the fences in one line, both chop saws could be placed pretty close to each other! | |||
{{Commissioning | {{Commissioning | ||
|IssueNumber= | |IssueNumber= | ||
|Naming=done | |Naming=done | ||
|NamingComment=Elektra | |NamingComment=Elektra Beckum KS 210 HM Plus | ||
|Picture= | |Picture= | ||
|PictureComment= | |PictureComment= | ||
Revision as of 14:35, 22 April 2019
| ToolInfoBox Herkules KSZ 2100 | |
|---|---|
| |
| Synonyms: | sliding compound miter saw; DE: Kappsäge, Kapp-, Zug- und Gehrungssäge |
| Type: | power tool/saw |
| Material: | wood |
| Used with: | circular saw blades, shop vac |
| Location: | chop saw station |
| Access Requirements: | upon introduction |
| Tutors: | Lukas |
| Manual: | ManualsLib |
| Similar (More or Less): | miter saw, circular saw, table saw, radial arm saw |
A chop saw is an electric miter saw (BE: mitre saw) and consists of a large circular saw and a sturdy frame. Movement of the saw head is restricted by a sliding rail which can be angled both vertically and horizontally ("compound miter").
For the hand tool capable of making only horizontally angled cuts, see miter saw.
This tool needs some additional upgrades but is already usable for small workpieces.
Safety
Always keep your hands clear of the blade path and use the machine's clamp and the back fence to hold your workpiece in place. Before turning on the power at all, make sure you understand how the saw head will move and double check that all restraints are properly and tightly adjusted.
Blade
Our saw is designed for saw blades measuring 210 × 30 × 2.8 mm (OD × bore × thickness).
The currently installed blade is a "Craftomat" 210 × 30 × 2.5 mm one with 64 carbide-tipped teeth.
Noise & Dirt
If you are not alone, ask the others whether it is okay to cut for a few minutes as they may have to interrupt their project to give you room and to protect their ears. Although the saw is not extremely loud, it is definitely startling when you are surprised by it turning on in your back!
It's advisable to hook up a shop vac for dust extraction as the passive collector bags that typically come with this kind of tool are not too efficient. Even the shop vac will let a lot of sawdust escape.
Maintenance
The blade should be sharpened or replaced when it becomes dull, otherwise using it is very dangerous! Tell a manager if you are noticing any problems, e.g. increased force required to cut your workpieces or poor quality cuts.
Decreased cutting ability can also result from dirt buildup - here are some cleaning instructions.
Potential Upgrades
- The work rests are crap and should be replaced by something, e.g. T-shaped wooden supports, at the proper height (see issue #11).
- It's possible to create a "shadow line" indicating your cut location by carefully positioning an LED right above the blade. [1]
- There is a clamping point on the right side of the blade, but when you actually put the clamp in there the motor will hit it. Could be fixed by adding a compatible hole (or simply another clamp) about 10 cm further to the right...very smart design -.-
Elektra Beckum KS 210 HM Plus
| ToolInfoBox Elektra Beckum KS 210 HM Plus | |
|---|---|
| |
| Synonyms: | compound miter saw; DE: Kappsäge, Kapp- und Gehrungssäge |
| Type: | power tool/saw |
| Material: | wood |
| Used with: | circular saw blades, shop vac |
| Location: | Commissioning shelf |
| Access Requirements: | chop saw introduction |
| Similar (More or Less): | miter saw, circular saw, table saw, radial arm saw |
Martin brought in an alternative chop saw, which needs to be commissioned before it can be used.
If we can get it set up on the same height as the other one and with the fences in one line, both chop saws could be placed pretty close to each other!
This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!
| Task | comment | Status |
|---|---|---|
| Name the tool: | Elektra Beckum KS 210 HM Plus | done |
| Take a picture | - | pending |
| Find the manual as PDF | needed for all machines - add a link to the InfoBox or comment where you could not find it | pending |
| Documentation | this page, status: in commissioning | pending |
| Print QR-Code | use the wikicrawler | pending |
| Introduction | - | pending |
| Security Check | to be done or witnessed by a manager | pending |
| Test | to be done or witnessed by a manager | pending |
| tool's name, owner and approx. value | provide to Patrick for inventorization | pending |
| Last step: make it available | physically and in the wiki - then delete this template | pending |
