Record Power DS300: Difference between revisions
Commissioning |
|||
| Line 11: | Line 11: | ||
|extrabox=yes | |extrabox=yes | ||
}} | }} | ||
{{Commissioning | |||
|IssueNumber= | |||
|Naming= | |||
|NamingComment= | |||
|Picture=done | |||
|PictureComment= | |||
|Manual= | |||
|ManualComment= | |||
|Documentation= | |||
|DocumentationComment=copied from belt and disc sander so far | |||
|QR= | |||
|QRComment= | |||
|Introduction= | |||
|IntroductionComment= | |||
|Security= | |||
|SecurityComment= | |||
|Test= | |||
|TestComment= | |||
|OwnerValue= | |||
|OwnerValueComment= | |||
|Availability= | |||
|AvailabilityComment= | |||
}} | |||
== Safety == | == Safety == | ||
| Line 24: | Line 47: | ||
* After 10 hours of operation: Check all screw connections and tighten if necessary | * After 10 hours of operation: Check all screw connections and tighten if necessary | ||
Refer to the manual in order learn more about the process to change | Refer to the manual in order learn more about the process to change the disc. | ||
=== Sandpaper Cleaning === | === Sandpaper Cleaning === | ||
| Line 31: | Line 54: | ||
<br clear=all> | <br clear=all> | ||
[[Category:Sanders]] | [[Category:Sanders]] | ||
[[Category:Sanding]] | [[Category:Sanding]] | ||
[[Category:Woodworking]] | [[Category:Woodworking]] | ||
Revision as of 13:50, 10 March 2025
| MachineInfoBox Big Disc Sander | |
|---|---|
| |
| Synonyms: | disk sander, disc sanding machine (BDSM); DE: Tellerschleifer (oder Schleifteller) |
| Material: | wood, metal |
| Used with: | sanding belts, sanding discs |
| Access Requirements: | |
| Manual: | in wooden box below the machine / similar machine on manualslib |
| Tutors: | |
| Similar (More or Less): | belt sander, disc sander |
This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!
| Task | comment | Status |
|---|---|---|
| Name the tool: | - | pending |
| Take a picture | - | done |
| Find the manual as PDF | needed for all machines - add a link to the InfoBox or comment where you could not find it | pending |
| Documentation | copied from belt and disc sander so far | pending |
| Print QR-Code | use the MachineQR Factory | pending |
| Introduction | - | pending |
| Security Check | to be done or witnessed by a manager | pending |
| Test | to be done or witnessed by a manager | pending |
| tool's name, owner and approx. value | provide to Johannes for inventorization | pending |
| Last step: make it available | physically and in the wiki - then delete this template | pending |
Safety
Always make sure to adhere to all precautions trained during the stationary sander introduction.
When sanding metal, never connect a dust extraction system, as sparks can ignite dust inside the vacuum, causing a smoldering fire. Always ensure proper ventilation and keep the sanding area free of flammable debris.
Maintenance
The machine does not require extensive maintenance. Service malfunctions and defects by trained persons only. Regular maintenance:
- After each workshift: Remove chips and sanding dust from the device
- After 10 hours of operation: Check all screw connections and tighten if necessary
Refer to the manual in order learn more about the process to change the disc.
Sandpaper Cleaning
Sandpaper can be restored a few times before it is used up by briefly sanding a piece of rubber! Instead of proper cleaning sticks you can apparently get great results with the sole of an old shoe - any donors? ;-)
