Handheld Routers

From CoMakingSpace Wiki

(Redirected from Trimmer)

MachineInfoBox

Routers

Router ActionShot.jpg
Synonyms: plunge routers, handheld routers,
electric trimmers, trimmer machines;
DE: Oberfräsen, Handoberfräsmaschinen
Material: wood
Used with: router bits;
router jigs
Access Requirements: Handheld Router Introduction
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis
Similar (More or Less): CNC router, router plane; milling table, CNC mill


A router is basically a powerful motor spinning a sharp metal bit at high speeds. Read the manual before using and be aware of the difference between the regular "push" and the more dangerous "climb" cut!

Safety

Routers are very dangerous tools, make sure you have received the handheld router introduction in person and take time to think about what you are going to do!


Makita DRT50

MachineInfoBox

Makita DRT50

Makita-DRT50.jpeg
Type: Handheld Routers
Location: Router Table
Access Requirements: Handheld Router Introduction
Status: Working
Manual: Makita
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis




The router has its own box (Makpack) with all its accessories (DRT50RTJX2). It is battery powered with 18V Makita lithium batteries that are shared with our other Makita tools like the cordless drill. The set consists of:

  • edge attachments (w/o grips; Kantenfräsmodule)
    • straight or adjustable angle
  • plunge attachment (with grips; Taucheinheit)
    • long grip (can replace one of the stud grips)
  • 2x vacuum dust attachment
  • edge roller attachment (Kantenfräsanschlag) for following edges using bits without a bearing

Dust Extraction

with a redundant adapter from our scroll saw, the router can be connected to Festool shop vacs

There are two different dust collection pieces, depending on which attachment you're using. Either one will need the black flexible adapter seen in the photo to fit on our shop vacs.

Additional Upgrades/Accessories

Freehand Baseplate

Lukas donated a custom baseplate bought from a local blogger (holzundleim.de). It should allow for much easier freehand routing!

It is made from HPL ("Resopal") and can be screwed to the straight edge attachment in place of its small round baseplate. To dive into the workpiece, let the baseplate rest on its rear (straight) side and slowly allow it to tip forward after the router bit reaches full speed.

installed baseplate

The grips were turned from scrap ash wood as the original 3D printed ones felt too small. As suggested by the maker, the bottom edges were broken with 120 grit sandpaper to improve its sliding ability.

Circle Cutting Jig

Patrick made a 3D printed circle cutting jig that is used in combination with the plunge attachment. Cutting range is ~200-720 mm ⌀ (depending on the router bit used).

Circle cutting jig


Clear Baseplate

Installing this baseplate to the plunge attachment gives you stability over large holes without obstructing your view!

clear baseplate resting on the walls of a cutlery tray



Ferm FBF-1050E

MachineInfoBox

Ferm FBF-1050E

Ferm FBF-1050E.JPG
Type: Handheld Routers
Location: Router Table
Access Requirements: Handheld Router Introduction
Status: Working
Manual: pdf
Tutors: Lukas
NitramLegov
Pakue
Johannes
Luzian
Keno
Utis



This router comes with 6 and 8 mm collets (Spannzangen). A few other accessories, including a parallel fence, can be found in its box.

this type of router was the first to be used in our old router table

Past repairs:


Router Bits

(main article: Router Bits)

Router bits can get quite expensive, but good quality ones can be sharpened when they become dull.

Typical collet (Spannzangen) sizes are 6 and 8 mm.
A simple shared set of 8 mm router bits is available under the router table. As always, report when broken and replace them accordingly!

Copying Rings

Copying rings can be used for template work and are more versatile (although a bit more complicated) than flush trim bits with a ball bearing that takes care of the copying. When working with a copying ring, the template has to be offset from the target shape by a few millimeters: offset = (outer coyping ring diameter - bit diameter)/2 [1]

Future Plans

  • self-built router table
  • 3D copying jig
  • "Pantorouter" guidance jig

Interesting Links