Prusa i3 MK2S (1): Difference between revisions
From CoMakingSpace Wiki
(added list of dangers) |
NitramLegov (talk | contribs) m (→Prusa i3 MK2S: assetid) |
||
| (33 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
== Prusa i3 MK2S (#1)== | |||
{{MachineInfoBox | {{MachineInfoBox | ||
|machine name=Original Prusa i3 MK2S | |machine name=Original Prusa i3 MK2S (#1) | ||
|image= | |image=Prusa i3 MK2S.JPG | ||
|synonyms= | |synonyms="P1", Prusa i3 MK2 ''(nearly identical)'' | ||
|type=3D | |type=3D Printer | ||
|material=plastic [[filament]] | |material=plastic [[filament]] | ||
|location=[[3D | |location=[[Location::3D Printing Area]] | ||
|status=Operational | |||
|status= | |||
|firmware=https://www.prusa3d.com/drivers/ | |firmware=https://www.prusa3d.com/drivers/ | ||
|software=[[Slic3r]] Prusa Edition | |software=[[Slic3r]] Prusa Edition | ||
|manual=[http://prusa3d.com/downloads/manual/prusa3d_manual_mk2s_en.pdf prusa3d.com] | |manual=[http://prusa3d.com/downloads/manual/prusa3d_manual_mk2s_en.pdf prusa3d.com] | ||
| | |assetid=5 | ||
}} | }} | ||
The Prusa i3 MK2S is our default 3D printer | The Prusa i3 MK2S is our default 3D printer. We have five of them, named "P1" through "P5". | ||
Please note that P1 has received an upgrade and now has a magnetic board. | |||
In addition to receiving a [[3D Printer Introduction|personal introduction]] from one of the tutors, make sure that you have read the [http://prusa3d.com/downloads/manual/prusa3d_manual_mk2s_en.pdf handbook] and use the latest version of [[Slic3r]] available at the [https://www.prusa3d.com/drivers/ drivers and manuals page]. | |||
The build volume of this model is 250{{x}}210{{x}}200 mm. | |||
<br clear=all> | |||
Latest revision as of 22:44, 6 November 2022
Prusa i3 MK2S (#1)
| MachineInfoBox Original Prusa i3 MK2S (#1) | |
|---|---|
| |
| Synonyms: | "P1", Prusa i3 MK2 (nearly identical) |
| Type: | 3D Printer |
| Material: | plastic filament |
| Location: | 3D Printing Area |
| Access Requirements: | 3D Printer Introduction |
| Status: | Operational |
| Firmware: | https://www.prusa3d.com/drivers/ |
| Software: | Slic3r Prusa Edition |
| Manual: | prusa3d.com |
| Tutors: | Lukas NitramLegov Pakue Mitja Lmnl99 Johannes Ciaran Luzian Leo Narquadah Kalunho Björn |
The Prusa i3 MK2S is our default 3D printer. We have five of them, named "P1" through "P5".
Please note that P1 has received an upgrade and now has a magnetic board.
In addition to receiving a personal introduction from one of the tutors, make sure that you have read the handbook and use the latest version of Slic3r available at the drivers and manuals page.
The build volume of this model is 250 × 210 × 200 mm.
