EleksMill: Difference between revisions

Revision as of 13:44, 6 September 2022

EleksMill

MachineInfoBox EleksMill

Synonyms:	DE: CNC-Fräse
Type:	CNC Router
Material:	just foam for now
Used with:	1/8" endmills
Location:	eRoom
Access Requirements:	CNC Router Introduction
Status:	working out initial problems
Software:	CAD/CAM software (e.g. Fusion 360); G-code sender
Tutors:	NitramLegov Pakue Johannes Luzian
Similar (More or Less):	CNC router

Mitja brought his "EleksMill" CNC router into our Space - it's small, but great for learning the basics of CNC Routing/routing as it shares the same workflow as the large WorkBee.

Important Facts

130 × 90 × 40 mm working range (less Z freedom depending on the length of your endmill!)
there are no endstops
- manually home the mill before a job
- you should use the (X/Y center, Z surface) as your origin
- make sure the size of your part does not exceed the working range!
motor speed: ???
compatible shaft diameter: 1/8" (3.175 mm)
controlled like the CNC router (Fusion 360 or similar CAD/CAM software; G-code sender)
- connection via USB - bring your own laptop!

Workholding

The mill has a 150 × 98 mm bed containing of 4 T-slots. clamping claws or similar workholders can be attached to it using M5 screws.

The current solution is not ideal, but many the workholding options for our larger CNC router should also be suitable if scaled down.

TO DO

figure out motor speed to calculate proper feedrates
what else?

Past Issues

screws/nuts used to come loose due to vibrations
- fixed with loctite or counternuts (where possible)
Z axis used to be too hard to turn => mill drifted deeper and deeper into the workpiece as upwards movements failed but downward movements were still possible
- was caused by a faulty spring

@@ Line 1: / Line 1: @@
-#REDIRECT[[CNC Mill#EleksMill]]
+== EleksMill ==
+{{MachineInfoBox
+|machine name=EleksMill
+|image=EleksMill.jpg
+|synonyms=DE: CNC-Fräse
+|type=CNC Router
+|material=just [[foam]] for now
+|location=[[Location::Electronics Room|eRoom]]
+|status=working out initial problems
+|firmware=
+|software=[[CAD]]/[[CAM]] software (e.g. [[Fusion 360]]); [[G-Code Senders|G-code sender]]
+|manual=
+|used with=1/8" [[endmills]]
+|similar=[[CNC Router|CNC router]]
+}}
+[[Mitja]] brought his [http://eleksmill.eleksmaker.com/ "EleksMill"] [[CNC Router|CNC router]] into our Space - it's small, but great for learning the basics of CNC [[Routing/routing]] as it shares the same workflow as the large [[WorkBee]].
+=== Important Facts ===
+* 130{{x}}90{{x}}40 mm working range (less Z freedom depending on the length of your [[endmill]]!)
+* there are '''no endstops'''
+** manually home the mill before a job
+** you should use the (X/Y center, Z surface) as your origin
+** make sure the size of your part does not exceed the working range!
+* motor speed: '''???'''
+* compatible shaft diameter: 1/8" (3.175 mm)
+* controlled like the [[CNC Router|CNC router]] ([[Fusion 360]] or similar [[CAD]]/[[CAM]] software; [[G-Code Senders|G-code sender]])
+** connection via USB - bring your own laptop!
+=== Workholding ===
+The mill has a 150{{x}}98 mm bed containing of 4 T-slots. [[Clamping Claws|clamping claws]] or similar workholders can be attached to it using M5 [[Metric Screws|screws]].
+The current solution is not ideal, but many the [[CNC Workholding|workholding options for our larger CNC router]] should also be suitable if scaled down.
+=== TO DO ===
+* figure out motor speed to calculate proper feedrates
+* ''what else?''
+=== Past Issues ===
+* screws/nuts used to come loose due to vibrations
+** fixed with [[loctite]] or counternuts (where possible)
+* Z axis used to be too hard to turn => mill drifted deeper and deeper into the workpiece as upwards movements failed but downward movements were still possible
+** was caused by a faulty spring
+<br clear=all>