Bandsaw Fence: Difference between revisions
From CoMakingSpace Wiki
(Created page with "{{ToolInfoBox |tool name=Simple Straight Fence |image=simple bandsaw fence.jpg |synonyms=parallel fence; DE: Bandsägen-Parallelanschlag |type=jig |status= |material= |use...") |
m (category bandsaw jigs) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{ToolInfoBox | {{ToolInfoBox | ||
|tool name=Simple Straight Fence | |tool name=Simple Straight Fence | ||
|image=simple bandsaw fence.jpg | |german=Bandsägen-Parallelanschlag|image=simple bandsaw fence.jpg | ||
|synonyms=parallel fence; DE: Bandsägen-Parallelanschlag | |synonyms=parallel fence; DE: Bandsägen-Parallelanschlag | ||
|type=[[jig]] | |type=[[Bandsaw Jig|bandsaw jig]] | ||
|status= | |status= | ||
|material= | |material= | ||
|used with=[[Bandsaws#Metabo BS 1638 W|Metabo BS 1638 W]] | |used with=[[Bandsaws#Metabo BS 1638 W|Metabo BS 1638 W]] | ||
|location=[[Location::Wood Workshop|wood workshop]] ( | |location=[[Location::Wood Workshop|wood workshop]] (''near'' [[bandsaw]]) | ||
|access=read this page | |access=read this page | ||
|tutors=[[ | |tutors=[[User:Lukas|Lukas]] | ||
|manual= | |manual= | ||
|donation= | |donation= | ||
|similar= | |similar=[[Bandsaw Sled|bandsaw sled]] | ||
}} | }} | ||
This bandsaw fence (made by [[User:Manu|Manu]]) looks similar to a parallel (or "rip") fence on the [[Table Saw|table saw]]. It is attached to the bandsaw's table with two small clamps. | This bandsaw fence (made by [[User:Manu|Manu]]) looks similar to a parallel (or "rip") fence on the [[Table Saw|table saw]]. It is attached to the bandsaw's table with two small clamps. | ||
| Line 19: | Line 19: | ||
Determine the correct angle by freehanding a cut along a straight line for a few cm, then set the fence according to your workpiece! | Determine the correct angle by freehanding a cut along a straight line for a few cm, then set the fence according to your workpiece! | ||
== Further Ideas == | |||
Next, we could make a magnet-held "point fence" like [https://m.youtube.com/watch?v=QeCRixeGGl8 Andrew Klein's really fancy one with integrated bearing "feather board"]! | |||
[[Category:Jigs]] | |||
[[Category:Bandsaw Jigs]] | |||
[[Category:Woodworking]] | [[Category:Woodworking]] | ||
Latest revision as of 23:30, 11 May 2024
| ToolInfoBox Simple Straight Fence | |
|---|---|
| |
| Synonyms: | parallel fence; DE: Bandsägen-Parallelanschlag |
| Type: | bandsaw jig |
| Used with: | Metabo BS 1638 W |
| Location: | wood workshop (near bandsaw) |
| Access Requirements: | read this page |
| Tutors: | Lukas |
| Similar (More or Less): | bandsaw sled |
This bandsaw fence (made by Manu) looks similar to a parallel (or "rip") fence on the table saw. It is attached to the bandsaw's table with two small clamps.
However, you may need to use it at a slight angle depending on the sawband! If the blade drifts, a parallel fence will only cause you trouble... Determine the correct angle by freehanding a cut along a straight line for a few cm, then set the fence according to your workpiece!
Further Ideas
Next, we could make a magnet-held "point fence" like Andrew Klein's really fancy one with integrated bearing "feather board"!
