Cordless Drills
| MachineInfoBox Cordless Drills | |
|---|---|
| |
| Synonyms: | cordless driver drills; DE: Akkuschrauber, Akkubohrschrauber |
| Material: | depending on the bit: screws, plastic, wood, metal |
| Used with: | drill bits, screwdriver bits |
| Access Requirements: | Drill Introduction |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
| Similar (More or Less): | drill press, screwdrivers, rotary tool, screw gun |
Cordless drills are very versatile tools and should not be missing from any workshop. Besides drilling, as the name implies, they are mostly used for driving screws ("electric screwdriver").
Here's a nice video about the internal mechanics of a typical drill!
Proper Use
Please follow these simple guidelines to avoid damage to your screws, material, or the drill itself:
- the torque (DE: Drehmoment) can typically be set with the ring before the chuck
- better start out too low than to round your screw in the first try - wood may also be damaged if screws (especially self-tapping/"Spax") are inserted too deep
- the drilling setting at the end of the scale should only be used for drilling, it creates way too much torque for screws and screwdriver bits!
- excessive torque does NOT make you screw faster, it really just wrecks stuff...
- there may also be variable speed settings (slider on top)
- only change when the drill is fully stopped
- use the slower one (1) for screwing to prevent slipping
- the higher speed can be used for drilling
Bits
- screwdriver bits and bit holders
- drill bits (shaft diameter typically limited to 10 mm)
Makita
Makita DDF484
| MachineInfoBox Makita DDF484 | |
|---|---|
| |
| Access Requirements: | Drill Introduction |
| Manual: | makita.de |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
We have two Makita DDF484 cordless drills. They have a 2 step metal gearbox for different drilling speeds. A torque limit for screwing can be set with the dial behind the chuck. Please use it to avoid breaking bits and screws due to too much torque! The chuck can hold up to 13mm drill bits.
One drill was donated by Ed and the batteries/charger are sponsored from multiple member donations, our Amazon Smile income as well as for the Tor4 workshops.
Makita DDF483
| MachineInfoBox Makita DDF483 | |
|---|---|
| |
| Access Requirements: | Drill Introduction |
| Manual: | makita |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
A smaller and lighter cordless drill, that is best paired with a 2Ah battery. Was bought via betterplace donations in 2022 and another one through a private donation in 2022.
Accessories
These were bought from member donations
- 2x 18V 3Ah Batteries (BL1830B)
- 1x charger (DC18RC)
- MAKPAC box for charger and batteries (usually underneath the drilling table)
Tor 4 aquisitions
- 2x 18V 5Ah batteries (BL1850B)
- 1x charger (DC18RC)
- MAKPAK box for charger, batteries and drill.
Betterplace donations
- 1x 18V 2Ah battery (BL1820B)
Private Tools
Bosch PSR 960
| MachineInfoBox Bosch PSR 960 | |
|---|---|
| |
| Access Requirements: | Drill Introduction |
| Manual: | in the box |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
Lukas has a Bosch PSR 960 you might be able to borrow! Unfortunately, its battery has gotten pretty bad.
It has six torque settings and only one speed.
- Power Supply
- There used to be two batteries, but one was quite old and only held its charge for a very short time. It was therefore upgraded to a corded pack.
- Charger for the intact one: "AL 1404", 7.2 to 14.4 V, 400 mA => 3 h charging time for the 1.2 Ah pack
- Please do not leave the battery in the charger for more than 3 or 4 hours, the old NiCd batteries will heat up and suffer from quite the memory effect!
