All public logs

Combined display of all available logs of CoMakingSpace Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 22:55, 31 October 2018 Lukas talk contribs uploaded File:Leimbinder.JPG (a beam of glued laminated timber in a hardware store)
• 16:35, 31 October 2018 Lukas talk contribs uploaded a new version of File:VHS couch table legs finished.JPG (4:3 aspect ratio for Main Page/Slideshow)
• 17:34, 27 October 2018 Lukas talk contribs uploaded a new version of File:Router table feed direction animation.GIF (low resolution - should allow animated thumbnails)
• 21:42, 25 October 2018 Lukas talk contribs uploaded File:Router table feed direction - fence.gif (low-resolution GIF animation of the proper feed direction for '''push cuts''' along the router table fence)
• 21:11, 25 October 2018 Lukas talk contribs uploaded File:Push block use.JPG ((fake) use of push blocks - press down firmly with both hands, but perhaps insert a bit for better routing results ;-))
• 21:03, 25 October 2018 Lukas talk contribs uploaded File:Making push blocks.JPG (gluing handles into a pair of push blocks, utilizing the offcuts to obtain an even clamping surface)
• 20:50, 25 October 2018 Lukas talk contribs uploaded File:Push blocks.JPG (two self-made push blocks to use with dangerous tools such as a router table, jointer or table saw)
• 21:02, 23 October 2018 Lukas talk contribs uploaded File:Digital file shredder-4.JPG (finished digital file shredder - clearly a desktop accessory that every Maker needs!)
• 21:00, 23 October 2018 Lukas talk contribs uploaded File:Digital file shredder-3.JPG (main case & inner works of the digital file shredder completed; power supply and baseplate still missing)
• 20:58, 23 October 2018 Lukas talk contribs uploaded File:Digital file shredder-2.JPG (most of the components for the digital file shredder are embedded into a 3D printed case after pausing the print at the appropriate time)
• 20:53, 23 October 2018 Lukas talk contribs uploaded File:Digital file shredder-1.JPG (rough assembly of the electronics for a small "file shredder" that formats SD cards!)
• 20:48, 23 October 2018 Lukas talk contribs uploaded File:Digital file shredder-0.JPG (a small "file shredder" that formats SD cards!)
• 20:27, 23 October 2018 Lukas talk contribs deleted page Plenum/Meeting minutes/2018-11 02 (unused redirect; content was: "#REDIRECT Plenum/Meeting minutes/2018-11-02", and the only contributor was "NitramLegov" (talk))
• 19:20, 23 October 2018 Lukas talk contribs uploaded File:Screenshot - Inkscape.PNG (screenshot of a typical Inkscape project (in this case: drawing wiki illustrations of woodturning tools))
• 16:34, 23 October 2018 Lukas talk contribs uploaded File:Router table feed direction.png (Basic schematic of the proper feed direction on a router table, resulting in safe climb cuts whichever side of the bit you are working on. Drawn in Inkscape, also see animated version: [[:File:Router table feed direction animation...)
• 16:24, 23 October 2018 Lukas talk contribs uploaded File:Router table feed direction animation.GIF (10 fps animation of the proper feed direction on a router table - only push cuts should be made! drawn in Inkscape, animated with GIMP)
• 16:44, 22 October 2018 Lukas talk contribs uploaded File:Westfalia router table off center.JPG (When we got the Westfalia router table, the router was mounted too far to the front so the bit would be off center - not that the scale on this simple table would have been too accurate anyway, but something we will fix nevertheless!)
• 16:41, 22 October 2018 Lukas talk contribs uploaded File:Westfalia router table fence-top.JPG (In addition to the fence, you should use additional guides on the router table whenever you can - shown here is a rigid top guide ''almost'' touching the workpiece, featherboards can actually press on it and are even safer!)
• 16:37, 22 October 2018 Lukas talk contribs uploaded File:Westfalia router table fence-X.JPG (The screw knob marked "X" should be left alone unless you really need it - it lets you move the left part of the fence back and forward on its own; for the majority of jobs on the router table (if not all) you want the fence to be perf...)
• 16:31, 22 October 2018 Lukas talk contribs uploaded File:Westfalia router table dust ports.JPG (there are two places where you can connect a shop vac to the Westfalia router table: top (green) - most useful for edge work - or bottom (black) - most useful for grooves)
• 17:00, 18 October 2018 Lukas talk contribs moved page Handbohrmaschinen Einweisung to Handbohrmaschinen-Einweisung without leaving a redirect
• 16:42, 18 October 2018 Lukas talk contribs deleted page 3D Druckern (unnötiger redirect, content was: "#REDIRECTPrusa i3 MK2S", and the only contributor was "Lmnl99" (talk))
• 22:48, 17 October 2018 User account Blacksheep talk contribs was created by Lukas talk contribs and password was sent by email (welcome!)
• 15:39, 13 October 2018 Lukas talk contribs uploaded File:Bosch EXPO2000.JPG (a Bosch EXPO2000 jigsaw in its case)
• 14:52, 13 October 2018 Lukas talk contribs deleted page Druckerhandbuch (Broken redirect: content was: "#REDIRECT[http://prusa3d.com/downloads/manual/prusa3d_manual_mk2s_en.pdf printers' manual]", and the only contributor was "Lmnl99" (talk))
• 16:21, 8 October 2018 Lukas talk contribs moved page Caulking Gun to Caulking Guns
• 16:10, 8 October 2018 Lukas talk contribs moved page Area Patron to Area Patrons
• 20:45, 30 September 2018 Lukas talk contribs uploaded File:File handles 12.JPG (a self-made file handle next to an "original" one)
• 20:44, 30 September 2018 Lukas talk contribs uploaded File:File handles 11.png (do NOT use a hammer to drive the file into a (self-made) file handle - the hardened steel could break - but instead push it in as far as you can and then hit the workbench surface with the handle's end a few times photo edited...)
• 20:29, 30 September 2018 Lukas talk contribs uploaded File:File handles 10.JPG (for drilling the hole in a self-made file handle, a stepped approach may be best but a first attempt with a drill bit about half the diameter of the thickest file shaft part was also successful)
• 20:26, 30 September 2018 Lukas talk contribs uploaded File:File handles 09.JPG (taking a self-made file handle off the wood lathe: you could do ''some'' of the work with a parting tool, but using a sharp saw with the lathe turned off is the safest way)
• 20:23, 30 September 2018 Lukas talk contribs uploaded File:File handles 08.JPG (Sanding on the wood lathe is awesome! Here, a self-made file handle gets its final touch)
• 20:20, 30 September 2018 Lukas talk contribs uploaded File:File handles 07.JPG (now it really looks like a self-made file handle: a groove has been formed with a skew chisel where it will feel comfortable)
• 19:42, 30 September 2018 Lukas talk contribs uploaded File:File handles 06.JPG (the blank for a self-made file handle is taking shape after some further smoothing with a skew chisel)
• 19:35, 30 September 2018 Lukas talk contribs uploaded File:File handles 05.JPG (a self-made file handle in progress: after roughing out a cylinder, a parting tool is used to get the proper diameter for a ferrule)
• 19:33, 30 September 2018 Lukas talk contribs uploaded File:File handles 04.JPG (turning blank for a self-made file handle set up between centers on the wood lathe)
• 18:16, 30 September 2018 Lukas talk contribs uploaded File:File handles 03.JPG (cutting a turning blank for a self-made file handle with a Japanese saw)
• 18:13, 30 September 2018 Lukas talk contribs uploaded File:File handles 02.JPG (measuring the ferrule for a self-made file handle with digital calipers - here you can truly appreciate that they always take an identical measurement for inside and outside with their two pairs of probes!)
• 18:09, 30 September 2018 Lukas talk contribs uploaded File:File handles 01.jpg (cutting a ferrule for a self-made file handle from steel pipe with a hacksaw)
• 17:04, 30 September 2018 Lukas talk contribs uploaded File:File handles cover.JPG (a self-made file handle still on the wood lathe)
• 19:26, 28 September 2018 Lukas talk contribs uploaded File:Woodturning scraper.svg (Sketch to illustrate the geometry of a woodturning scraper (b: bevel angle). Drawn with Inkscape.)
• 19:05, 28 September 2018 Lukas talk contribs uploaded File:Skew chisel.svg (Sketch to illustrate the geometry of a skew chisel (b: bevel angle, s: skew angle). Drawn with Inkscape.)
• 18:40, 28 September 2018 Lukas talk contribs uploaded File:Spindle gouge.svg (Sketch to illustrate the geometry of a spindle gouge (b: bevel angle). Drawn with Inkscape.)
• 18:31, 28 September 2018 Lukas talk contribs uploaded File:Roughing gouge.svg (Sketch to illustrate the geometry of a roughing gouge (b: bevel angle). Drawn with Inkscape.)
• 18:26, 28 September 2018 Lukas talk contribs uploaded a new version of File:Fingernail bowl gouge.svg (square version)
• 18:25, 28 September 2018 Lukas talk contribs uploaded a new version of File:Bowl gouge.svg (square version)
• 18:21, 28 September 2018 Lukas talk contribs uploaded File:Bowl gouge.svg (Sketch to illustrate the geometry of a bowl gouge (b: bevel angle). Drawn with Inkscape.)
• 18:13, 28 September 2018 Lukas talk contribs uploaded File:Fingernail bowl gouge.svg (Sketch to illustrate the geometry of a "fingernail" bowl gouge (b: bevel angle). Drawn with Inkscape.)
• 20:33, 27 September 2018 Lukas talk contribs uploaded File:VHS table 08.jpg (both VHS couch table legs finished and in front of their couch)
• 20:30, 27 September 2018 Lukas talk contribs uploaded File:VHS table 07.JPG (the top board of a VHS couch table leg is made of two carefully laid out pieces to give a bit of extra stability from the inside and let each leg double as a side table when the large top is removed)