NU-POWER MABG 006AMA

MachineInfoBox NU-POWER MABG 006AMA

Synonyms:	bench top grinder, grinding wheel; DE: Doppelschleifer, Schleifbock, Trockenschleifmaschine
Material:	metal (not aluminum)
Access Requirements:	The query description has an empty condition.Property "Needs Introduction" (as page type) with input value "The query description has an empty condition." contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process.
Tutors:	The query description has an empty condition.
Similar (More or Less):	disc grinder, files, sandpaper

... further resultsProperty "Has caption" (as page type) with input value "Vertical Bandsaws, Vertical Bandsaws, CNC Router, Mechanical Hand Tool, 3D Printers, 3D Printers, 3D Printers, 3D Printers, 3D Printers, 3D Printers, Oscilloscope, Oscillating Tool, Multimeters, Chop Saw, Belt and Disc Sander, Bench Grinders, Bench Grinders, Table Saw, Handheld Circular Saws, Shop Vacs, Dust Extractors, Biscuit Joiner, Chop Saw, Handheld Circular Saws, CNC Router, Compressor, Archived:Corded Drills, Archived:Corded Drills, Cordless Drills, Cordless Disc Grinder, Cordless Drills, Jigsaws, Vice, Lab Power Supplies, Lab Power Supplies, Corded Disc Grinder, Corded Disc Grinder, Wood Lathes, CNC Mill, Wood Lathes, Laser Cutter, Eccentric Sanders, Kitchen Equipment, Chop Saw, Wood Lathe Accessory, Laser Printers, Audio Equipment, Audio Equipment, Wood Lathe Accessory, Wood Lathe Accessory[[:Special:Ask/-5B-5BHas-20Internal-20AssetID::+-5D-5D/-3FHas-20Internal-20Category/mainlabel=-2D/limit=50/offset=50/format=plainlist/link=none/headers=hide/default=NU-2DPOWER-20MABG-20006AMA" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process.<ul><li>"]]" is not a number.</li> <li>Some use of "" in your query was not closed by a matching "".</li></ul>|]]

We got this old bench grinder used but still in good condition; the wheels run true and quietly. The grinder is equipped with two different stone wheels with different grits; one for heavy-duty and quick material removal, one for a finer and more precise material removal that will leave a way nicer surface finish.

Take care: there is no prevention of turning on after loss & restoration of power (keine Anlaufsicherung)! Besides, the motor takes quite a long time to run down after it was turned off.

This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!

Task	comment	Status
Name the tool:	-	done
Take a picture	-	pending
Find the manual as PDF	needed for all machines - add a link to the InfoBox or comment where you could not find it	not available
Documentation	nearly the same as previous bench grinder	done
Print QR-Code	use the MachineQR Factory	pending
Introduction	unchanged	done
Security Check	better than before: runs more truly, spark covers over both wheels	done
Test	to be done or witnessed by a manager	done
tool's name, owner and approx. value	donated by Joe	pending
Last step: make it available	physically and in the wiki - then delete this template	pending

Specs

wheel diameter: 6" (approx. 15 cm)
motor: 1/2 hp
speed: 2950 rpm
serial number: 898853

Maintenance

The wheels need to be "dressed" from time to time in order to produce nice straight edges and maintain stability. There is a T-shaped diamond file for this on the grinding table.

Apparently, it's also possible to dress a stone with nothing more than a few spring washers on a piece of threaded rod!^[1]

Changing Wheels

After installing a new grinding wheel, set up a safety perimeter (let's say everyone leaves the room) and let the grinder run for five minutes. Only if that went well, without suspicious noises or visible signs of problems, should the grinder be used again.