Project:Disc Sander: Difference between revisions

Revision as of 16:12, 27 June 2019

This is a wish list page - we don't have this tool yet!

ToolInfoBox Disc Sander

Synonyms:	disk sander; DE: Tellerschleifer, Schleifteller
Type:	sander
Status:	under construction
Material:	wood
Used with:	250 mm sanding discs (velcro, no holes)
Location:	Lukas (proper place TBD)
Access Requirements:	help finish the build ;-)

Lukas is building a disc sander that is driven by the "Güde 1000" wood lathe! It should not be that hard to do but the awkward work angle may be a disadvantage.

build progress:

sanding disc ✔
- find out which maximum size would fit on the lathe - 320 mm according to its wiki page ✔
- find out which sizes of sanding discs (Schleifscheiben) are common and affordable in that range - 250 mm (approx. 10") looks good ✔
- make a faceplate for the lathe ✔
- apply velcro disc ✔
- do a bit of test sanding ✔
table
- sturdy box that can be mounted on the lathe bed
- miter fence
- dust extraction
- (optional?) tilting top
commissioning

Speed

Comparable tools are run with speeds between 250 and 750 m/min. Therefore, only the lowest speed of the lathe should be used to drive the sanding disc (850 rpm -> approx. 667 m/min at the edge).

Cleaning

Sandpaper can be restored a few times before it is used up by briefly sanding a piece of rubber! Instead of proper cleaning sticks you can apparently get great results with the sole of an old shoe - any donors? ;-)

@@ Line 3: / Line 3: @@
 {{ToolInfoBox
 |tool name=Disc Sander
-|image=
+|image=disc sander test.JPG
 |synonyms=disk sander; DE: Tellerschleifer, Schleifteller
-|type=
+|type=[[sander]]
 |status=[https://github.com/comakingspace/do-something/issues/119 under construction]
 |material=[[wood]]
-|used with=
+|used with=250 mm [[Sanding Discs|sanding discs]] (velcro, no holes)
-|location=
+|location=''[[Lukas]]'' (proper place TBD)
-|access=
+|access=help finish the build ;-)
 |tutors=
 |manual=
@@ Line 16: / Line 16: @@
 |similar=
 }}
-{{£}} will try to [https://github.com/comakingspace/do-something/issues/119 build a disc sander] that is driven by the "Güde 1000" [[Wood Lathe|wood lathe]]! It should not be that hard to do but the awkward work angle may be a disadvantage.
+{{£}} is [https://github.com/comakingspace/do-something/issues/119 building a disc sander] that is driven by the "Güde 1000" [[Wood Lathe|wood lathe]]! It should not be that hard to do but the awkward work angle may be a disadvantage.
+'''build progress:'''
+# sanding disc ✔
+#* find out which maximum size would fit on the lathe - '''320 mm''' according to its wiki page ✔
+#* find out which sizes of sanding discs (''Schleifscheiben'') are common and affordable in that range - '''250 mm''' (approx. 10") looks good ✔
+#* make a faceplate for the lathe ✔
+#* apply velcro disc ✔
+#* do a bit of test sanding ✔
+# table
+#* sturdy box that can be mounted on the lathe bed
+#* miter fence
+#* dust extraction
+#* (optional?) tilting top
+# [[commissioning]]
-Important preparations:
-* find out which maximum size would fit on the lathe - '''320 mm''' according to its wiki page
-* find out which sizes of sanding discs (''Schleifscheiben'') are common and affordable in that range - '''250 mm''' (approx. 10") looks good
-* '''make''' or get a faceplate for the lathe (in progress)
-* apply velcro disc
-* start sanding
 == Speed ==
-[https://www.proxxon.com/de/micromot/28060.php Comparable tools] are run with speeds between 250 and 750 m/min. Therefore, only the lowest speed of the lathe should be used to drive the sanding disc (850 rpm -> approx. 667 m/min at the edge).
+[https://www.proxxon.com/de/micromot/28060.php Comparable tools] are run with speeds between 250 and 750 m/min. Therefore, '''only the lowest speed of the lathe should be used''' to drive the sanding disc (850 rpm -> approx. 667 m/min at the edge).
 == Cleaning ==
@@ Line 32: / Line 40: @@
+[[Category:Sanders]]
 [[Category:Sanding]]
 [[Category:Self-Made Tools]]
 [[Category:Woodworking]]