Makita DRT50: Difference between revisions

Latest revision as of 00:53, 3 September 2024

Makita DRT50

MachineInfoBox Makita DRT50

Type:	Handheld Routers
Location:	Router Table
Access Requirements:	Handheld Router Introduction
Status:	Working
Manual:	Makita
Tutors:	Lukas NitramLegov Pakue Johannes Luzian Keno Utis

The router has its own box (Makpack) with all its accessories (DRT50RTJX2). It is battery powered with 18V Makita lithium batteries that are shared with our other Makita tools like the cordless drill. The set consists of:

edge attachments (w/o grips; Kantenfräsmodule)
- straight or adjustable angle
plunge attachment (with grips; Taucheinheit)
- long grip (can replace one of the stud grips)
2x vacuum dust attachment

edge roller attachment (Kantenfräsanschlag) for following edges using bits without a bearing

edge attachment without grips
edge attachment with roller added
edge attachment that can be angled -45º – 30º
plunge attachment
plunge attachment, one grip replaced with the long variant

Dust Extraction

with a redundant adapter from our scroll saw, the router can be connected to Festool shop vacs

There are two different dust collection pieces, depending on which attachment you're using. Either one will need the black flexible adapter seen in the photo to fit on our shop vacs.

Additional Upgrades/Accessories

Freehand Baseplate

Lukas donated a custom baseplate bought from a local blogger (holzundleim.de). It should allow for much easier freehand routing!

It is made from HPL ("Resopal") and can be screwed to the straight edge attachment in place of its small round baseplate. To dive into the workpiece, let the baseplate rest on its rear (straight) side and slowly allow it to tip forward after the router bit reaches full speed.

installed baseplate

The grips were turned from scrap ash wood as the original 3D printed ones felt too small. As suggested by the maker, the bottom edges were broken with 120 grit sandpaper to improve its sliding ability.

Circle Cutting Jig

Patrick made a 3D printed circle cutting jig that is used in combination with the plunge attachment. Cutting range is ~200-720 mm ⌀ (depending on the router bit used).

Clear Baseplate

Installing this baseplate to the plunge attachment gives you stability over large holes without obstructing your view!

clear baseplate resting on the walls of a cutlery tray

@@ Line 36: / Line 36: @@
 {{£}} donated a [https://www.holzundleim.de/2020/11/die-makita-grundplatte-mit-doppelgriff/ custom baseplate bought from a local blogger] (holzundleim.de). It should allow for much easier freehand routing!
-It is made from [[HPL]] ("Resopal") and can be screwed to the gripless surface attachment in place of its small round baseplate. To dive into the workpiece, let the baseplate rest on its rear (straight) side and slowly allow it to tip forward after the router bit reaches full speed.
+It is made from [[HPL]] ("Resopal") and can be screwed to the straight edge attachment in place of its small round baseplate. To dive into the workpiece, let the baseplate rest on its rear (straight) side and slowly allow it to tip forward after the router bit reaches full speed.
 [[File:wide DRT50 baseplate.jpg|thumb|installed baseplate]]
@@ Line 43: / Line 43: @@
 ==== Circle Cutting Jig ====
-{{P}} made a 3D printed [[Circle Routing Jig|circle cutting jig]] that is used in combination with the surface attachment. Cutting range is ~200-720 mm ⌀ (depending on the router bit used).
+{{P}} made a 3D printed [[Circle Routing Jig|circle cutting jig]] that is used in combination with the plunge attachment. Cutting range is ~200-720 mm ⌀ (depending on the router bit used).
 [[File:Router Circle Jig.jpg|left|frameless|Circle cutting jig]]
+<br clear=all>
+==== Clear Baseplate ====
+Installing this baseplate to the plunge attachment gives you stability over large holes without obstructing your view!
+[[File:clear DRT50 baseplate.jpg|thumb|clear baseplate resting on the walls of a cutlery tray]]
 <br clear="all>