Drill Presses: Difference between revisions
From CoMakingSpace Wiki
NitramLegov (talk | contribs) m (Add type) |
|||
| (32 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
{{MachineInfoBox | {{MachineInfoBox | ||
|machine name= | |machine name=''Drill Presses'' | ||
|german=Säulenbohrmaschinen | |||
|image=Drill press TB13-5ED.jpg | |image=Drill press TB13-5ED.jpg | ||
|synonyms=bench | |synonyms=bench drills, pillar drills, column drills;<br>DE: Säulenbohrmaschinen,<br>"Tischbohrmaschinen",<br>"Bohrständer", "Senkbohrer" | ||
|location=[[Location::Drilling Table|drilling table]] | |location=[[Location::Drilling Table|drilling table]] | ||
|material=depending on the [[Drill Bits|drill bit]]:<br>[[wood]], [[plastic]], [[metal]] | |material=depending on the [[Drill Bits|drill bit]]:<br>[[wood]], [[plastic]], [[metal]] | ||
|similar=[[Drill Stand|drill stand]], other [[drills]] | |similar=[[Drill Stand|drill stand]], other [[drills]] | ||
|used with=[[Drill Bits|drill bits]], [[inclinometer]] | |used with=[[Drill Bits|drill bits]], [[inclinometer]] | ||
|type=Drills | |||
|extrabox=yes | |||
}} | }} | ||
To use a drill press, you'll need to mount a [[Bits#Drill Bits|drill bit]] that suits your workpiece and securely fasten it with the chuck key. | |||
== Safety == | == Safety == | ||
| Line 39: | Line 35: | ||
* [https://www.instructables.com/id/Homemade-Vertical-Drill-Press-Clamp/ vertical clamp] (very simple, basically to board with a hinge at one end) | * [https://www.instructables.com/id/Homemade-Vertical-Drill-Press-Clamp/ vertical clamp] (very simple, basically to board with a hinge at one end) | ||
<br clear="all" /> | |||
<br clear=all> | <!-- NOTE: The following block "imports" content from separate pages - please don't change the code! To edit the actual information, please go back and click "edit" next to the section headline you are interested in :-) --> | ||
{{#ask: | |||
[[MachineType::Drill Presses]] | |||
|order=ascending | |||
|format=embedded | |||
|embedonly=yes | |||
{{ | |||
[[ | |||
| | |||
| | |||
| | |||
}} | }} | ||
Latest revision as of 23:20, 24 October 2022
| MachineInfoBox Drill Presses | |
|---|---|
| |
| Synonyms: | bench drills, pillar drills, column drills; DE: Säulenbohrmaschinen, "Tischbohrmaschinen", "Bohrständer", "Senkbohrer" |
| Material: | depending on the drill bit: wood, plastic, metal |
| Used with: | drill bits, inclinometer |
| Access Requirements: | Drill Introduction |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
| Similar (More or Less): | drill stand, other drills |
To use a drill press, you'll need to mount a drill bit that suits your workpiece and securely fasten it with the chuck key.
Safety
- read the manual!
- get a personal introduction by one of the tutors!
- wear personal protection, but never operate the drill press with gloves on!
- don't drill materials with harmful dust!
- make sure there is nobody nearby who might be surprised by a piece of shrapnel flying their way!
- use a machine vise for small workpieces!
- never use a machine vise on top of a wooden board or two wooden boards at the same time (tower rule)!
Fastening Options
a lever clamp can be used for some workpieces such as this door handle shaft
- we should get one or two of these drill press locking clamps if they are available around here
- additional tables to mount on the simple "standard" one are probably worth the effort
- inspiration: Stephan Pöhnlein on YouTube
Jigs
Some ideas what we should make for a more efficient/safe use of a drill press:
- V-block for drilling into round or angled things
- vertical clamp (very simple, basically to board with a hinge at one end)
Scheppach DP 16 SL
| MachineInfoBox Scheppach DP 16 SL | |
|---|---|
| |
| Type: | Drill Presses |
| Location: | Drilling Table |
| Access Requirements: | Drill Introduction |
| Status: | Working |
| Manual: | bahag.com |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
Blacksheep kindly donated a Scheppach DP 16 SL drill press in August 2019.
From a technical point of view, it offers the following:
- Drill mount: 1 - 16 mm (neues Futter)
- Speed:
510800 - 2430 rpm
Drill Speeds
When changing the belt position, unlock the the motor hinge with the screw on the right side. Then move the belt on the pulley that reduces the diameter and afterwards change the belt position on the second pulley (similar to changing the chain on a bike). When the belt is in its final position, it should be level (waagerecht) and have enough slack so the motor can be pushed back and re-locked with the screw.
The slowest speed is currently not available due to a broken pulley!
Depth Stop
The original depth stop collar broke relatively soon, so Patrick designed a 3D printable replacement part.
After several reprints that were broken soon after installation, we removed the stop screw so the collar only holds the safety shield now...
Speed Chart
This chart was specifically created for the speeds that the Scheppach can provide. You can find it taped to the top of the machine.
ZJ5116 TB 16
| MachineInfoBox ZJ5116 TB 16 | |
|---|---|
| |
| Type: | Drill Presses |
| Location: | Drilling Table |
| Access Requirements: | Drill Introduction |
| Status: | Working |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
- Drill bit sizes: 1-16mm (neues Futter)
- Transmission: 16 gear (170-3080rpm)
According to the sign on the machine and this document, the machine has the following (relevant) specs:
| Specification | Value |
|---|---|
| Motor Power | 550 W |
| Spindle Travel | 85 mm |
| U/min | 170-3080 |
| Spindle Taper | MT2 |
| Table size | 290 mm × 290 mm |
Speed Chart
This chart was specifically created for the speeds that the machine can provide. You can find it taped to the right side of the machine. Not all speeds are used for this chart if you want/ need very precise control you should look up a more detailed table.
