Router Table

MachineInfoBox Westfalia Universal Frästisch Nr. 64 56 97
Synonyms:	DE: Frästisch, Oberfrästisch, stationäre Oberfräse
Material:	wood
Used with:	routers, push blocks
Access Requirements:	The query description has an empty condition.Property "Needs Introduction" (as page type) with input value "The query description has an empty condition." contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process.
Manual:	Westfalia
Tutors:	The query description has an empty condition.

... further resultsProperty "Has caption" (as page type) with input value "Vertical Bandsaws, Vertical Bandsaws, CNC Router, Mechanical Hand Tool, 3D Printers, 3D Printers, 3D Printers, 3D Printers, 3D Printers, 3D Printers, Oscilloscope, Oscillating Tool, Multimeter, Chop Saw, Wanted:Handheld Belt Sander, Bench Grinders, Bench Grinders, Table Saw, Handheld Circular Saws, Dust Extractors, Dust Extractors, Biscuit Joiner, Chop Saw, Handheld Circular Saws, CNC Router, Compressor, Archived:Corded Drills, Archived:Corded Drills, Cordless Drills, Cordless Disc Grinder, Cordless Drills, Jigsaws, Vice, Lab Power Supplies, Lab Power Supplies, Corded Disc Grinder, Corded Disc Grinder, Wood Lathes, CNC Mill, Wood Lathes, Laser Cutter, Eccentric Sanders, Kitchen Equipment, Chop Saw, Wood Lathe Accessory, Laser Printers, Audio Equipment, Audio Equipment, Wood Lathe Accessory, Wood Lathe Accessory[[:Special:Ask/-5B-5BHas-20Internal-20AssetID::+-5D-5D/-3FHas-20Internal-20Category/mainlabel=-2D/limit=50/offset=50/format=plainlist/link=none/headers=hide/default=Router-20Table" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process."{{{assetid}}}" is not a number.|]]

A router table turns a handheld router into a stationary tool. The router gets attached to the router table upside down in order to enable the workpiece to be fed through the router (thus, it is for a router what a table saw is for a circular saw).

push cuts at the fence: right to left!

the proper workpiece direction to make push cuts depends on which side of the bit you're cutting on!

It is very important to realize that the exposed router bit is not only dangerous because of its sharp edges, but also because it can rip the workpiece out of your hand and let it fly across the workshop, or pull your hand into the danger zone. To make sure that you are in control and not the router, ONLY make push cuts, i.e. ONLY feed workpieces through from the right to the left side if you are working in front of the router bit and vice-versa! You should understand why this is important after getting the router introduction or reading articles about accidental climb cuts on the internet.

Please also see Project:Router Table in case you would like to join us in building your own.

(Emergency) Stop

To stop the router, you can slap the lid of the yellow switchbox or use the foot switch. When stopping inside a cut, the foot switch is highly recommended so you can keep your hands on the workpiece for full control!

Setup

Dust Extraction

For edge work, you can use the top (green) dust port in the fence, but for grooves you should connect the shop vac to the bottom (black) dust port on the router itself. Keep in mind that the top port will only work if there is at least a small gap in the fence!

It will still be pretty messy work - a router generates lots of shavings - but should help reduce the amount of fine dust flying around.

Fence

don't mess with the "X"!

The fence consists of several parts which need to be aligned carefully if you want it to be accurate. In most cases (working with a parallel fence), you will not need the knob labeled "X", so please don't mess with it too much...the next user will thank you!

There is a scale on the table to set the fence's distance from the center of the router bit, but it is rather rough and doesn't allow accurate fine measurements. A height/depth gauge, easily made from a caliper and some scrap wood, would be a nice solution (similar to this Instructable, but there are better ones around for sure).

use additional guides whenever you can

Once you have your bit inserted, the fence's two sliding front sections should be brought as close together as possible for maximum workpiece support and a focused airflow to the dust extraction port. The top guide should be brought down until it nearly touches your workpiece. The frontal guide works the same - we should make compatible featherboards that could actually press the workpiece to the table/fence for even more support.

Unfortunately, the current screw knobs have to be turned very tightly or vibrations will cause everything to shift over time - perhaps we can exchange these knobs with locking levers so that they can be adjusted without pliers.

Improvements/Upgrades

Any modifications to the table or router itself should be discussed with the owner (Martin) in advance and security-checked by a manager afterwards!

done:

• 3D printed shop vac adapter (needed some further adjustment with the table saw) - is the file available somewhere?
• cut two protruding corners from the front guide bracket so it stay mounted to the table all the time without getting in the way
• make push blocks

further ideas:

the router is not properly centered yet

• properly align the mounting plate with the router (currently off-center!)
• make featherboards with slots that fit to the existing guide brackets
• repair the height adjustment screw of the KingCraft router that is currently broken (in the box on the ladder shelf)
• replace (at least) the star knobs connecting the fence and the table with locking levers or knobs with hex nuts that can be gripped with wrenches (do those exist?)
• make (or buy) a height/depth gauge to set the fence distance or bit height

==> video showing these (and more) potential upgrades: Heiko Rech - Tipps zum Arbeiten mit dem Frästisch (DE)

Compatible Routers

• The KingCraft KBF-1050E router is currently attached to the table.

More to be determined...