Metal Lathes: Difference between revisions
m (a.k.a. Drehe) |
(Sanding: André's advice to prevent damage) |
||
| Line 23: | Line 23: | ||
We are '''still in need of a grease gun''' (something like [https://www.myford.co.uk/acatalog/MYFORD-OIL-GUN--15472-1770.html#SID=239 this], a.k.a. oil gun or ''Fettpresse'') to lubricate through the oil nipples. If we buy [https://www.fk-soehnchen.de/werkstatt/werkstattbedarf/fettpressen-zubehoer/schmiernippel/Kegelschmiernippel-DIN-71412.html replacement oil nipples with metric thread], the grease gun should fit those (and ideally still the original ones, although unlikely). | We are '''still in need of a grease gun''' (something like [https://www.myford.co.uk/acatalog/MYFORD-OIL-GUN--15472-1770.html#SID=239 this], a.k.a. oil gun or ''Fettpresse'') to lubricate through the oil nipples. If we buy [https://www.fk-soehnchen.de/werkstatt/werkstattbedarf/fettpressen-zubehoer/schmiernippel/Kegelschmiernippel-DIN-71412.html replacement oil nipples with metric thread], the grease gun should fit those (and ideally still the original ones, although unlikely). | ||
== Sanding == | |||
You can use [[sandpaper]] to quickly finish the surface of a piece you've turned on the lathe. When doing this, '''place a [[Shop Rags|shop rag]] on the lathe bed to prevent pieces of the abrasive from getting dragged into the mechanics''' where they might cause some damage! | |||
== Further Reading == | == Further Reading == | ||
Revision as of 15:16, 27 December 2017
| MachineInfoBox Myford ML7 | |
|---|---|
| |
| Synonyms: | metalworking lathe, engine lathe, machinists' lathe; DE: "Drehbank", Zug- und Leitspindeldrehmaschine, "Drehe" |
| Used with: | tool bits |
| Access Requirements: | Metal Lathe Introduction |
| Tutors: | Pakue Johannes Luzian |
| Similar (More or Less): | wood lathe |
We were generously given a Myford ML7 metalworking lathe.
It is currently being restored (see corresponding issue), more information will be added as work progresses!
Lubrication
There are various oil nipples (2 B.A. thread; Schmiernippel) all over the machine and two sight-feed lubricators (a.k.a. drip feed oilers) above the headstock spindle bearings.
The manufacturer's recommendation is "Esso Nuto 32" gear oil but we are using a more viscous "90" oil as that was available to us and two trusted sources ensured us it should work just fine.
Oil Nipples
According to the manufacturer's assembly diagrams, there should be 3 oil nipples on the carriage, 2 on the "motorizing" section, 1 on the tailstock, 2 on the headstock, 2 on the "bed, leadscrew and gear train" section and 1(+2) on the quick change gearbox for a total of 11 "2BA oil nipples 33/072" and 2 "Lumatic HDFV4/45" (if we have that quick change gearbox). However, a few of those (at least 3) are missing!
We are still in need of a grease gun (something like this, a.k.a. oil gun or Fettpresse) to lubricate through the oil nipples. If we buy replacement oil nipples with metric thread, the grease gun should fit those (and ideally still the original ones, although unlikely).
Sanding
You can use sandpaper to quickly finish the surface of a piece you've turned on the lathe. When doing this, place a shop rag on the lathe bed to prevent pieces of the abrasive from getting dragged into the mechanics where they might cause some damage!
