HBM AS188: Difference between revisions
(→Specifications: outlet thread, pressure also in psi; fixed some typos) |
|||
| Line 12: | Line 12: | ||
|similar=[[compressor]] | |similar=[[compressor]] | ||
|location=[[Location::Airbrush Area|airbrush area]] | |location=[[Location::Airbrush Area|airbrush area]] | ||
|assetid= | |assetid=157}} | ||
This compressor is dedicated to be used with [[airbrushing]] equipment and must '''not''' be used otherwise! | This compressor is dedicated to be used with [[airbrushing]] equipment and must '''not''' be used otherwise! | ||
Revision as of 14:59, 23 April 2024
HBM AS188
This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!
| Task | comment | Status |
|---|---|---|
| Name the tool: | Was bought as "Airbrush Kompressor Model ArtisticLife 188 (al188)" - tag on the machine itself says "AS 188"(Link to HBM) | Done |
| Take a picture | - | Done |
| Find the manual as PDF | For googling, please see the naming comment | pending |
| Documentation | this page, status: in commissioning | done |
| Print QR-Code | use the wikicrawler | Done |
| Introduction | Airbrush Introduction | done |
| Security Check | to be done or witnessed by a manager | done |
| Test | to be done or witnessed by a manager | ??? |
| tool's name, owner and approx. value | Done | Done |
| Last step: make it available | physically and in the wiki - then delete this template | pending |
| MachineInfoBox HBM AS188 | |
|---|---|
| |
| Synonyms: | DE: Airbrush-Kompressor |
| Type: | Airbrush Compressor |
| Material: | airbrush paint |
| Used with: | airbrushes |
| Location: | Airbrush Area |
| Access Requirements: | Airbrush Introduction |
| Status: | Working |
| Tutors: | Björn |
| Similar (More or Less): | compressor |
This compressor is dedicated to be used with airbrushing equipment and must not be used otherwise!
Manual
We're still looking for the PDF manual for this exact model. The manual for a similar model (AS-186) can be found here.
Recommended Pressure Settings for Airbrushing
Our compressor has 2 air outlets, each of which has its own pressure gauge. The output pressure can be adjusted by turning the blue "on/off" knob next to the pressure gauge.
The required pressure setting depends on a number of factors such as
- type of paint (thicker paints require higher pressures, for example our "Aero Pearl" and "Aero Shine" effect colors)
- airbrush needle diameter
- gravity feed (paint compartment at the top, for example our Iwata Neo airbrush)
- syphon feed (paint bottle below the airbrush, for example our black Bader Ideal 350 airbrush)
Apart from the above, the "ideal" pressure setting also depends on personal preference. As a rule of thumb, start with low pressure and slowly go higher. For our Iwata Neo (a double action, gravity feed airbrush), start with 15-20 psi. The pressure should be high enough to create a good atomised misty spray from your airbrush, but also low enough to allow for control of the trigger.
A higher pressure setting atomises the paint better, but this also results in faster drying time.
Specifications
- outlet thread: 1/8" BSP
- tank capacity: 3 liters
- working pressure: 0.2 - 4 bar (3-58 psi)
- engine power: 150 watts (1/6 HP)
- number of cylinders: 1
- voltage: 220 - 240 V
- noise level: approx. 50 dB (A)
- net air yield: 23 L/minute
- weight: 8.6 kg
Both outlets have their own pressure regulator and pressure gauge.
Built-in moisture separator in the tank.
Thermal safety and overpressure protection above 6 bar.
Oil-free compressor.
How to Connect an Airbrush to the Compressor
To connect the compressor hose to an airbrush, please use the adaptor piece. The compressor will keep its pressure even if no airbrush is connected.
