Cordless Drills: Difference between revisions
From CoMakingSpace Wiki
(removed DeWALT and added another small Makita drill) |
NitramLegov (talk | contribs) m (Change to Machine Inclusion) |
||
| (6 intermediate revisions by 2 users not shown) | |||
| Line 3: | Line 3: | ||
|image=drilling wood.gif | |image=drilling wood.gif | ||
|synonyms=cordless driver drills;<br>DE: Akkuschrauber,<br>Akkubohrschrauber | |synonyms=cordless driver drills;<br>DE: Akkuschrauber,<br>Akkubohrschrauber | ||
|material=depending on the bit:<br>[[screws]], [[plastic]], [[wood]], [[metal]] | |material=depending on the bit:<br>[[screws]], [[plastic]], [[wood]], [[metal]] | ||
|location= | |location=[[Location::Drilling Table|drilling table]] | ||
|similar=[[Drill Press|drill press]], [[screwdrivers]],<br>[[Rotary Tool|rotary tool]], screw gun | |similar=[[Drill Press|drill press]], [[screwdrivers]],<br>[[Rotary Tool|rotary tool]], screw gun | ||
|used with=[[Drill Bits|drill bits]], [[Screwdriver Bits|screwdriver bits]] | |used with=[[Drill Bits|drill bits]], [[Screwdriver Bits|screwdriver bits]] | ||
|type=Drills | |||
|extrabox=yes | |extrabox=yes | ||
}} | }} | ||
Cordless drills are very versatile tools and should not be missing from any workshop. Besides drilling, as the name implies, they are mostly used for driving screws ("electric screwdriver"). | Cordless drills are very versatile tools and should not be missing from any workshop. Besides drilling, as the name implies, they are mostly used for driving screws ("electric screwdriver"). | ||
| Line 35: | Line 29: | ||
* [[Bits#Drill Bits|drill bits]] (shaft diameter typically limited to 10 mm) | * [[Bits#Drill Bits|drill bits]] (shaft diameter typically limited to 10 mm) | ||
<br clear=all> | <br clear="all" /> | ||
<!-- NOTE: The following block "imports" content from separate pages - please don't change the code! To edit the actual information, please go back and click "edit" next to the section headline you are interested in :-) --> | |||
{{MachineInclusion|order=ascending}} | |||
{{ | |||
| | |||
}} | |||
== Accessories == | |||
'''These were bought from member donations''' | '''These were bought from member donations''' | ||
| Line 84: | Line 49: | ||
<br clear=all> | <br clear=all> | ||
[[Category:Drills]] | [[Category:Drills]] | ||
Latest revision as of 19:42, 19 September 2023
| MachineInfoBox Cordless Drills | |
|---|---|
| |
| Synonyms: | cordless driver drills; DE: Akkuschrauber, Akkubohrschrauber |
| Material: | depending on the bit: screws, plastic, wood, metal |
| Used with: | drill bits, screwdriver bits |
| Access Requirements: | Drill Introduction |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
| Similar (More or Less): | drill press, screwdrivers, rotary tool, screw gun |
Cordless drills are very versatile tools and should not be missing from any workshop. Besides drilling, as the name implies, they are mostly used for driving screws ("electric screwdriver").
Here's a nice video about the internal mechanics of a typical drill!
Proper Use
Please follow these simple guidelines to avoid damage to your screws, material, or the drill itself:
- the torque (DE: Drehmoment) can typically be set with the ring before the chuck
- better start out too low than to round your screw in the first try - wood may also be damaged if screws (especially self-tapping/"Spax") are inserted too deep
- the drilling setting at the end of the scale should only be used for drilling, it creates way too much torque for screws and screwdriver bits!
- excessive torque does NOT make you screw faster, it really just wrecks stuff...
- there may also be variable speed settings (slider on top)
- only change when the drill is fully stopped
- use the slower one (1) for screwing to prevent slipping
- the higher speed can be used for drilling
Bits
- screwdriver bits and bit holders
- drill bits (shaft diameter typically limited to 10 mm)
Makita DDF483 (#1)
| MachineInfoBox Makita DDF483 (#1) | |
|---|---|
| |
| Type: | Cordless Drills |
| Location: | Drilling Table |
| Access Requirements: | Drill Introduction |
| Status: | Working |
| Manual: | makita |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
A smaller and lighter cordless drill, that is best paired with a 2Ah battery. Was bought via betterplace donations in 2022 and another one through a private donation in 2022.
Makita DDF483 (#2)
| MachineInfoBox Makita DDF483 (#2) | |
|---|---|
|
| |
| Type: | Cordless Drills |
| Location: | Drilling Table |
| Access Requirements: | Drill Introduction |
| Status: | Working |
| Manual: | makita |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
Makita DDF484 (#1)
| MachineInfoBox Makita DDF484 (#1) | |
|---|---|
| |
| Type: | Cordless Drills |
| Location: | Drilling Table |
| Access Requirements: | Drill Introduction |
| Status: | Working |
| Manual: | makita.de |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
We have two Makita DDF484 cordless drills. They have a 2 step metal gearbox for different drilling speeds. A torque limit for screwing can be set with the dial behind the chuck. Please use it to avoid breaking bits and screws due to too much torque! The chuck can hold up to 13mm drill bits.
One drill was donated by Ed and the batteries/charger are sponsored from multiple member donations, our Amazon Smile income as well as for the Tor4 workshops.
Makita DDF484 (#2)
| MachineInfoBox Makita DDF484 (#2) | |
|---|---|
|
| |
| Type: | Cordless Drills |
| Location: | Drilling Table |
| Access Requirements: | Drill Introduction |
| Status: | Working |
| Manual: | makita.de |
| Tutors: | Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Keno Jakob |
Accessories
These were bought from member donations
- 2x 18V 3Ah Batteries (BL1830B)
- 1x charger (DC18RC)
- MAKPAC box for charger and batteries (usually underneath the drilling table)
Tor 4 aquisitions
- 2x 18V 5Ah batteries (BL1850B)
- 1x charger (DC18RC)
- MAKPAK box for charger, batteries and drill.
Betterplace donations
- 1x 18V 2Ah battery (BL1820B)
