Drying Ovens: Difference between revisions

Revision as of 07:08, 2 September 2022

Memmert UM 400 (#2)

MachineInfoBox Memmert UM 400 (#2)

Synonyms:	DE: Trockenöfen (Sg. Trockenofen)
Type:	Drying Ovens
Used with:	heat-resistant gloves
Location:	Hot Metal Area
Access Requirements:
Status:	Working
Manual:	frankshospitalworkshop.com
Tutors:
Similar (More or Less):	pizza oven

According to the dials, this oven could reach a temperature of around 250°C. However, the nominal temperature according to the manufacturer is 220°C.

It has about 38 × 38 × 33 cm (width × height × depth) free space inside (about 2 cm more between the ridges on the sides, top and bottom).

Memmert UM 400 (#1)

MachineInfoBox Memmert UM 400 (#1)

Synonyms:	DE: Trockenöfen (Sg. Trockenofen)
Type:	Drying Ovens
Used with:	heat-resistant gloves
Location:	3D Printing Area
Access Requirements:
Status:	Working
Manual:	frankshospitalworkshop.com
Tutors:
Similar (More or Less):	pizza oven

According to the dials, this oven could reach a temperature of around 250°C. However, the nominal temperature according to the manufacturer is 220°C.

It has about 38 × 38 × 33 cm (width × height × depth) free space inside (about 2 cm more between the ridges on the sides, top and bottom).

House Rules

Use common sense - a running oven consumes a lot of energy and can even be a fire hazard. Therefore, do not leave an oven running when you leave the Space!

Uses

Feel free to try whatever is safe, i.e. certainly won't damage the oven or any people!

So far, members have used these ovens to...

melt plastic (only with good ventilation!)
cure paint or epoxy more quickly
dry moist filament before 3D printing
shrink-fitting: expand one metal piece to insert a second one (e.g. a bearing) that's been contracted by cold
...?

after this scooter part was heated in a drying oven and the bearings were cooled down with freeze spray, the parts slid together easily and became solidly connected once everything was back at the same temperature

It may also be possible to temper metal after hardening - has anyone tried?

@@ Line 1: / Line 1: @@
-{{MachineInfoBox
+{{MachineInclusion}}
-|machine name=Drying Ovens
-|german=Trockenöfen
-|image=drying oven.JPG
-|synonyms=DE: Trockenöfen (Sg. Trockenofen)
-|type=
-|material=
-|location=[[Location::Electronics Room|eRoom]], [[Location::Metal Workshop|metal workshop]]
-|access=upon reading
-|status=working
-|firmware=
-|software=
-|manual=
-|tutors=
-|used with=heat-resistant [[gloves]]
-|similar=pizza oven
-}}
-We got two decommissioned lab drying ovens that can be used like a normal kitchen oven, with the important difference that these ovens are for non-food items.
-They should be able to reach temperatures around 250°C (according to the dials).
+==House Rules ==
-== House Rules ==
 Use common sense - a running oven consumes a lot of energy and can even be a fire hazard. Therefore, '''do not leave an oven running when you leave the Space!'''
-== Uses ==
+==Uses==
 Feel free to try whatever is safe, i.e. certainly won't damage the oven or any people!
 So far, members have used these ovens to...
-* [[Project:Precious Plastic|melt plastic]] (only with good ventilation!)
+*[[Project:Precious Plastic|melt plastic]] (only with good ventilation!)
-* cure paint or [[epoxy]] more quickly
+*cure paint or [[epoxy]] more quickly
-* dry moist [[filament]] before [[3DP|3D printing]]
+*dry moist [[filament]] before [[3DP|3D printing]]
-* shrink-fitting: expand one [[metal]] piece to insert a second one (e.g. a [[bearing]]) that's been contracted by cold
+*shrink-fitting: expand one [[metal]] piece to insert a second one (e.g. a [[bearing]]) that's been contracted by cold
 * ''...?''
@@ Line 36: / Line 17: @@
 It may also be possible to [[temper]] metal after hardening - has anyone tried?
 [[Category:Heat]]
 [[Category:Metalworking]]