Project:Resized Wardrobe Drawers: Difference between revisions
m (cost & tools) |
(→Build Photos: added them all!) |
||
| Line 24: | Line 24: | ||
File:resized wardrobe drawers 03.JPG|one of the old drawers taken apart to take measurements of its components | File:resized wardrobe drawers 03.JPG|one of the old drawers taken apart to take measurements of its components | ||
File:resized wardrobe drawers 04.JPG|plans taking shape on a [[Common Room|common room]] table | File:resized wardrobe drawers 04.JPG|plans taking shape on a [[Common Room|common room]] table | ||
File:resized wardrobe drawers 05.JPG|parts fresh off the [[Table Saw|table saw]] | |||
File:resized wardrobe drawers 06.JPG|test piece for the bottom groove on the new [[Router Table|router table]] | |||
File:resized wardrobe drawers 07.JPG|all pieces with the bottom groove cut out | |||
File:resized wardrobe drawers 08.JPG|first "dry" fit without [[Wood Screws|screws]] and [[Dowel Pegs|dowel pegs]] | |||
File:resized wardrobe drawers 09.JPG|parts labeled with their final place (1/2, right/left) | |||
File:resized wardrobe drawers 10.jpg|a piece of [[Masking Tape|masking tape]] is a great quick & dirty depth stop | |||
File:resized wardrobe drawers 11.JPG|[[Dowel Centers|dowel centers]] really help with the hole alignment - no measuring needed! | |||
File:resized wardrobe drawers 12.JPG|all "wall" pieces cut, routed and drilled | |||
File:resized wardrobe drawers 13.JPG|an [[Eccentric Sanders|eccentric sander]] made quick work of [[sanding]] the bottom pieces | |||
File:resized wardrobe drawers 14.JPG|scribing the ideal screw line for the [[Butt Joint|butt joints]] in the back with a [[Marking Gauge|marking gauge]] | |||
File:resized wardrobe drawers 15.JPG|[[Butt Joint|butt joint]] drilled as marked before | |||
File:resized wardrobe drawers 16.JPG|[[leveling]] one of the [[Drawer Slides|slides]] | |||
File:resized wardrobe drawers 17.JPG|first installation attempt was too low - the slides were then raised by one [[yardstick]] thickness | |||
File:resized wardrobe drawers 18.JPG|once the first drawer was installed, it became painfully clear that the shelf above had warped... | |||
File:resized wardrobe drawers 19.JPG|...and the "walls" of the top drawer had to be [[Table Saw|ripped]] to fit in the smaller-than-measured space. | |||
File:resized wardrobe drawers 20.JPG|done! | |||
</gallery> | </gallery> | ||
[[Category:Furniture]] | [[Category:Furniture]] | ||
[[Category:Woodworking]] | [[Category:Woodworking]] | ||
Revision as of 20:46, 12 November 2018
| ProjectInfoBox Resized Wardrobe Drawers | |
|---|---|
| |
| Status: | build done, now documenting |
| Release Date: | Oct 2018 |
| Initiator: | Lukas |
| Materials Used: | film faced plywood, melamine, pine plywood, dowel pegs, wood screws, drawer slides |
| Tools Used: | table saw, router table, cordless drill, marking gauge |
| Approx. Cost: | approx. 15 € for wood, 20 € for slides |
Our wardrobe (forgot from which furniture store) had two drawers that were 36 cm deep, but there was room for 54 cm - wasted potential for a 50 % increase of usable space!
Of course, that had to be changed and I tackled this project as soon as we got our first router table running in the CoMakingSpace.
Notes
- originally wanted to replace just the sides, but different style of slides, higher walls & thicker bottom desired
- ...
Build Photos
- mouseover/click for more information!
the wasted space before this project - the cheap (weak & short) drawer slides were probably one of the reasons against including full-size drawers
old drawers taken out to take measurements of the wardrobe
one of the old drawers taken apart to take measurements of its components
plans taking shape on a common room table
parts fresh off the table saw
test piece for the bottom groove on the new router table
all pieces with the bottom groove cut out
first "dry" fit without screws and dowel pegs
parts labeled with their final place (1/2, right/left)
a piece of masking tape is a great quick & dirty depth stop
dowel centers really help with the hole alignment - no measuring needed!
all "wall" pieces cut, routed and drilled
an eccentric sander made quick work of sanding the bottom pieces
scribing the ideal screw line for the butt joints in the back with a marking gauge
butt joint drilled as marked before
first installation attempt was too low - the slides were then raised by one yardstick thickness
once the first drawer was installed, it became painfully clear that the shelf above had warped...
...and the "walls" of the top drawer had to be ripped to fit in the smaller-than-measured space.
done!
