Metal Lathes: Difference between revisions
m (linked "similar") |
(→Lubrication: oil nipples) |
||
| Line 14: | Line 14: | ||
== Lubrication == | == Lubrication == | ||
There are various oil nipples (''2 B.A.'' thread) all over the machine and two sight-feed lubricators (a.k.a. drip feed oilers) above the headstock spindle bearings. | There are various oil nipples (''2 B.A.'' thread; ''Schmiernippel'') all over the machine and two sight-feed lubricators (a.k.a. drip feed oilers) above the headstock spindle bearings. | ||
The [https://www.myford.co.uk/acatalog/VG32-LUBRICATING-OIL---ESSO-NUTO-32---1-LITRE-662.html manufacturer's recommendation] is "Esso Nuto 32" gear oil but we are using a more viscous "90" oil as that was available to us and two trusted sources ensured us it should work just fine. | The [https://www.myford.co.uk/acatalog/VG32-LUBRICATING-OIL---ESSO-NUTO-32---1-LITRE-662.html manufacturer's recommendation] is "Esso Nuto 32" gear oil but we are using a more viscous "90" oil as that was available to us and two trusted sources ensured us it should work just fine. | ||
'''We are still in need of | === Oil Nipples === | ||
According to the manufacturer's [https://www.myford.co.uk/acatalog/Myford_ML7.html assembly diagrams], there should be 3 oil nipples on the carriage, 2 on the "motorizing" section, 1 on the tailstock, 2 on the headstock, 2 on the "bed, leadscrew and gear train" section and 1(+2) on the quick change gearbox for a total of 11 "2BA oil nipples 33/072" and 2 "Lumatic HDFV4/45" (if we have that quick change gearbox). '''However, a few of those (at least 3) are missing!''' | |||
We are '''still in need of a grease gun''' (something like [https://www.myford.co.uk/acatalog/MYFORD-OIL-GUN--15472-1770.html#SID=239 this], a.k.a. oil gun or ''Fettpresse'') to lubricate through the oil nipples. If we buy [https://www.fk-soehnchen.de/werkstatt/werkstattbedarf/fettpressen-zubehoer/schmiernippel/Kegelschmiernippel-DIN-71412.html replacement oil nipples with metric thread], the grease gun should fit those (and ideally still the original ones, although unlikely). | |||
== Further Reading == | == Further Reading == | ||
Revision as of 17:11, 19 December 2017
| MachineInfoBox Myford ML7 | |
|---|---|
| |
| Synonyms: | "metal lathe", engine lathe, machinists' lathe; DE: "Drehbank", Zug- und Leitspindeldrehmaschine |
| Access Requirements: | Metal Lathe Introduction |
| Tutors: | Pakue Johannes Luzian |
| Similar (More or Less): | wood lathe |
We were generously given a Myford ML7 metalworking lathe.
It is currently being restored (see corresponding issue), more information will be added as work progresses!
Lubrication
There are various oil nipples (2 B.A. thread; Schmiernippel) all over the machine and two sight-feed lubricators (a.k.a. drip feed oilers) above the headstock spindle bearings.
The manufacturer's recommendation is "Esso Nuto 32" gear oil but we are using a more viscous "90" oil as that was available to us and two trusted sources ensured us it should work just fine.
Oil Nipples
According to the manufacturer's assembly diagrams, there should be 3 oil nipples on the carriage, 2 on the "motorizing" section, 1 on the tailstock, 2 on the headstock, 2 on the "bed, leadscrew and gear train" section and 1(+2) on the quick change gearbox for a total of 11 "2BA oil nipples 33/072" and 2 "Lumatic HDFV4/45" (if we have that quick change gearbox). However, a few of those (at least 3) are missing!
We are still in need of a grease gun (something like this, a.k.a. oil gun or Fettpresse) to lubricate through the oil nipples. If we buy replacement oil nipples with metric thread, the grease gun should fit those (and ideally still the original ones, although unlikely).
