Punches: Difference between revisions
(Created page with "Punches are small tools driven with a hammer, e.g. in order to leave a mark or a hole. == Center Punches == {{ToolInfoBox |tool name=Center Punch |image=center pu...") |
(→Drift Punches: aka, location, other variants) |
||
| Line 49: | Line 49: | ||
|tool name=Drift Punch | |tool name=Drift Punch | ||
|image=drift punch.JPG | |image=drift punch.JPG | ||
|synonyms=DE: Durchtreiber,<br>Nageltreiber | |synonyms=DE: Durchtreiber,<br>Nageltreiber, Durchschlag | ||
|type=hand tool | |type=hand tool | ||
|access=upon reading | |access=upon reading | ||
|location= | |location=above [[Drilling Table|drilling table]] | ||
|material=[[nails]] | |material=[[nails]] | ||
|used with=[[hammers]] | |used with=[[hammers]] | ||
|similar=pin punch | |similar=pin punch | ||
}} | }} | ||
Use this punch to align drilled pieces, e.g. for [[Rivets|riveting]], or to drive [[nails]] in a little deeper without leaving ugly [[Hammers|hammer]] marks. | Use this punch to align drilled pieces, e.g. for [[Rivets|riveting]], or to drive [[nails]] in a little deeper without leaving ugly [[Hammers|hammer]] marks. There are also varieties with a cupped end for the nail head to disappear into, but we just have a simple straight one. | ||
Also useful for removing nail fragments from [[Scrap Wood|scrap wood]]! | Also useful for removing nail fragments from [[Scrap Wood|scrap wood]]! | ||
Revision as of 16:55, 19 December 2017
Punches are small tools driven with a hammer, e.g. in order to leave a mark or a hole.
Center Punches
| ToolInfoBox Center Punch | |
|---|---|
| |
| Synonyms: | DE: Körner |
| Type: | hand tool |
| Material: | metal, wood, plastic |
| Used with: | hammers |
| Access Requirements: | upon reading |
If you want to mark something harder than the listed materials such as stone or concrete, just use a cheap nail instead of this tool!
Hole Punches
| ToolInfoBox Hole Punches | |
|---|---|
| |
| Synonyms: | leather punches; DE: Locheisen, Ausschlageisen, Stanzeisen |
| Type: | hand tool |
| Material: | fabric, leather, paper, foam rubber |
| Used with: | hammers |
| Access Requirements: | upon reading |
| Similar (More or Less): | punch pliers |
For smaller holes, see punch pliers. For the common office tool, see two-hole punch.
As seen towards the end of a very interesting lamp build on YouTube, chucking a hole punch into a drill may actually work pretty well to cut wooden plugs (verification needed)!
Available sizes:
- 2.5 mm
- 3 mm
- 4 mm
- 5 mm
- 6 mm
- 7 mm
- 8 mm
- 9 mm
- 10 mm
Drift Punches
| ToolInfoBox Drift Punch | |
|---|---|
| |
| Synonyms: | DE: Durchtreiber, Nageltreiber, Durchschlag |
| Type: | hand tool |
| Material: | nails |
| Used with: | hammers |
| Location: | above drilling table |
| Access Requirements: | upon reading |
| Similar (More or Less): | pin punch |
Use this punch to align drilled pieces, e.g. for riveting, or to drive nails in a little deeper without leaving ugly hammer marks. There are also varieties with a cupped end for the nail head to disappear into, but we just have a simple straight one.
Also useful for removing nail fragments from scrap wood!
