Tyme Avon: Difference between revisions
(→Accessoires: turned into gallery for better overview; we'd also run into problems with headline hierarchies if embedded) |
NitramLegov (talk | contribs) m (→Tyme Avon: german) |
||
| (3 intermediate revisions by one other user not shown) | |||
| Line 5: | Line 5: | ||
|image=Tyme Avon ATL301.jpg | |image=Tyme Avon ATL301.jpg | ||
|type=Wood Lathe | |type=Wood Lathe | ||
|german=Drechselbank | |||
|material=[[Woodturning Blanks|woodturning blanks]] | |material=[[Woodturning Blanks|woodturning blanks]] | ||
|location=[[Location::Woodturning Area|woodturning area]] | |location=[[Location::Woodturning Area|woodturning area]] | ||
| Line 37: | Line 38: | ||
<br clear="all" /> | <br clear="all" /> | ||
=== | ===Accessories=== | ||
<gallery> | <gallery> | ||
File:Wood Lathe Tool Rest - Bent.jpg|An alternative tool rest for our Tyme Avon | File:Wood Lathe Tool Rest - Bent.jpg|An alternative tool rest for our Tyme Avon | ||
| Line 43: | Line 44: | ||
</gallery> | </gallery> | ||
'''Click the photos below for more information!''' | |||
{{#ask: | {{#ask: | ||
[[Category:Tools]] [[Used With::Tyme Avon]] | [[Category:Tools]] [[Used With::Tyme Avon]] | ||
| Line 55: | Line 57: | ||
| widths = 200 | | widths = 200 | ||
}} | }} | ||
=== Spare Parts === | |||
Many spare parts can be found via [https://incamachines.com/english/multico-tyme-graduate/tyme-spare-parts.html incamachines.com]. | |||
The current driving belt is labeled with "190J6 TBA POLY-V 483J6" and "2088". | |||
Latest revision as of 14:06, 18 July 2024
Tyme Avon
| MachineInfoBox Tyme Avon ATL301 | |
|---|---|
| |
| Type: | Wood Lathes |
| Material: | woodturning blanks |
| Used with: | face shield, woodturning tools |
| Location: | Woodturning Area |
| Access Requirements: | Woodturning Introduction |
| Status: | Working |
| Tutors: | Lukas |
The Tyme Avon is an old, but solidly built lathe that has replaced our flimsy Güde 1000.
Specs
We seem to have the Model ATL301 with 36" (915 mm) between centers and a bed length of 52" (1320 mm).
- max. workpiece diameter (above bed): 280 mm (11")
- max. workpiece diameter (swiveled 90°): 495 mm (19.5")
- max. workpiece diameter (swiveled 180°): 610 mm (24")
- max. workpiece length: 900 mm
- spindle speeds: 470 - 750 - 1150 - 2000 rpm
- motor: 550 W (3/4 hp)
- spindle thread: M25 × 2 mm; internal No. 2 morse taper (MK2)
- workholding options:
- headstock: drive center, faceplate, four-jaw chuck, ...
- tailstock: No. 2 morse taper (MK2) - accessories: rotating centers, our "usual" drill chucks also fit
Speed Selection
The lathe can run at various speeds depending on which pulleys are connected by the belt:
Do not put excessive tension on the belt - you'll be very happy about the belt slipping in case you've made a mistake and the tool digs into the workpiece!
New belts are still sold at store.lathes.co.uk
Accessories
An alternative tool rest for our Tyme Avon
We have two barrels which can be used with the Tyme Avon - we are usually using the right one, since it spins with the workpiece.
Click the photos below for more information!
Four-Jaw Chucks
Precision Combination Chuck
Spare Parts
Many spare parts can be found via incamachines.com.
The current driving belt is labeled with "190J6 TBA POLY-V 483J6" and "2088".
