Table Saw and Soldering Irons: Difference between pages

Latest revision as of 22:26, 4 February 2024

MachineInfoBox Soldering Irons

Synonyms:	DE: Lötkolben
Material:	solder
Access Requirements:	Soldering Iron Introduction
Tutors:	Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Leo Erik
Similar (More or Less):	hot air soldering station

A soldering iron is a basic hand tool used to connect electronic components. The principle of working with a soldering iron lies in melting – as the name suggests – solder in order to conductively connect electrical components.

The normal soldering temperature is around 300°C varying from solder types and thermal capacity of the electronic parts or the soldering iron. Also the higher the power output of the soldering iron is the better it will melt larger amounts of solder or heat up bigger components.

How to Use

Preparations:

make room for soldering – crowded and messy workplaces only make the work more difficult
get solder (should be in the top drawer on the left side of the e-bench)
wet the cleaning sponge (if needed, usually in the soldering station)
check if your electronic parts are ready and nothing is missing

Next, heat up the soldering iron to around 300°C. When the solder melts by touching to tip, the iron is ready for use.
Try not to melt the solder directly on the tip but rather heat your components with the soldering iron and then apply solder to the parts. This will result in an optimal flow of the liquid solder and avoid "cold solder joints". If the joint is shining like a polished piece of metal then the soldering was successful and a reliable electrical connection was made.
Clean the tip afterwards with the brass wool and/or the wet sponge that's usually integrated into the iron's "station".

Ask a tutor if you have any questions or want an introduction into soldering. This video tutorial on splicing and soldering wires or the mikrocontroller.net page "Löten" (DE) may also be interesting.

Safety

Please be careful while handling a soldering iron as it gets very hot! Mind your surroundings and other people to avoid injuries.
Avoid breathing in the smoke forming after melting solder. It isn't as much the lead vapor but the flux which is quite unhealthy when inhaled. If you plan on soldering for an extended amount of time consider using an extraction fan to reduce exposure.
Be aware to wash your hands after handling electronic components as the flux and the lead in the solder are toxic when absorbed through mucous membranes. Avoid touching your face or food while soldering to minimize contact.

PACE ADS200

MachineInfoBox PACE ADS200

Synonyms:	DE: Lötkolben
Type:	Soldering Irons
Material:	solder
Location:	Electronics Area
Access Requirements:	Soldering Iron Introduction
Status:	Working
Tutors:	Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Leo Erik
Similar (More or Less):	hot air soldering station

Pace Soldering Station with 120W and cartridge heaters

Available Tips

Standard 1130-0003-P1 (0.40mm Conical Sharp Bent 30°)
Standard 1130-0008-P1 (1.20mm 30° Chisel)
Ultra 1131-0055-P1 (6.35mm Chisel)

If you need a different tip shape, they can be ordered from Welectron. Donations are always welcome!

KSGER T12 V2.1

MachineInfoBox KSGER T12

Synonyms:	DE: Lötkolben
Type:	Soldering Irons
Material:	solder
Location:	Electronics Area
Access Requirements:	Soldering Iron Introduction
Status:	Working
Tutors:	Lukas NitramLegov Pakue Lmnl99 Johannes Luzian Leo Erik
Similar (More or Less):	hot air soldering station

The KSGER soldering station used the T12 heating cartridges from Hakko (or their aftermarket copies). These are directly heated with an integrated temperature sensor and are therefore faster to heat up.

Note: During first heat up the station may show an error, but it should go away once it is at the desired temperature.

Accessories

Soldering Fume Extraction

With::Soldering Irons]]}}

AccessoryInfoBox Soldering Fume Extraction

Synonyms:	DE: Lötrauchabsaugung
Used with:	Soldering Irons

Please use a soldering fume extraction when soldering in order to take care of harmful fumes. If the filter is full, you can get a replacement at Reichelt.

@@ Line 1: / Line 1: @@
 {{MachineInfoBox
-|machine name=Bosch PTS 10
+|machine name=Soldering Irons
-|image=cutting corners.JPG
+|german=Lötkolben
-|synonyms=sawbench, bench saw;<br>DE: Tischkreissäge, TKS, Baukreissäge,<br>Baustellenkreissäge, stationäre Kreissäge
+|synonyms=DE: Lötkolben
-|type=power tool/[[:Category:Saws|saw]]
+|image=KSGER_T12_soldering_station.jpeg
-|access=[[Table Saw Introduction]] - not alone
+|location=[[Location::Electronics Area]]
-|location=[[Location::Wood Workshop|wood workshop]]
+|material=[[solder]]
-|material=[[wood]]
+|similar=[[Hot Air Soldering Station|hot air soldering station]]
-|used with=[[Push Sticks|push sticks]], [[Circular Saw Blades|circular saw blades]], [[Shop Vac|shop vac]]
+|extrabox=yes
-|tutors=[[Tutor::User:Lukas|Lukas]]
-|manual=[https://www.bosch-do-it.de/media/garden/gardenmedia/manuals/1305037_160992A3VE_201705pdf..pdf bosch-do-it.de]
-|similar=[[Circular Saw|circular saw]], [[Chop Saw|chop saw]]
 }}
-'''This is one of the most dangerous but also one of the most versatile [[woodworking]] tools.'''
+A soldering iron is a basic hand tool used to connect [[Electronic Components|electronic components]]. The principle of working with a soldering iron lies in melting – as the name suggests – [[solder]] in order to conductively connect electrical components.
-Did you know you can also turn a [[Rotary Tool|rotary tool]] into a micro table saw?
+The normal soldering temperature is '''around 300°C''' varying from solder types and thermal capacity of the electronic parts or the soldering iron. Also the higher the power output of the soldering iron is the better it will melt larger amounts of solder or heat up bigger components.
-== Health & Safety ==
+== How to Use ==
-Unless we get our hands on a [http://www.sawstop.com/ stopping table saw], this is a machine that can take fingers off. Take precautions to prevent the worst from happening!
+Preparations:
-* read the manual
+* make room for soldering – crowded and messy workplaces only make the work more difficult
-* '''get a [[Table Saw Introduction|personal introduction]]'''
+* get solder (should be in the top drawer on the left side of the e-bench)
-* gloves: make an informed decision
+* wet the cleaning sponge (if needed, usually in the soldering station)
-** some sources say you should wear them to protect yourself against splinters which could surprise you and make your hand flinch in a dangerous position
+* check if your electronic parts are ready and nothing is missing
-** others prohibit the use of gloves as your entire hand could be dragged into the blade if one gets caught
-* double-check that the riving knife (splitter) is in line with the blade - it prevents the workpiece from catching on the rear of the blade and being hurled towards you ("kickback")
-** [https://www.youtube.com/watch?v=mEn3mTEu8pw this video] explains this and other dangers pretty nicely!
-** [https://youtu.be/u7sRrC2Jpp4?t=150 this video] is a demonstration of what kickback looks like
-* wear [[Personal Protection#Ear Defenders|ear defenders]] and [[Personal Protection#Goggles|safety goggles]]
-** a new belt might [https://www.youtube.com/watch?v=Nc4Mt-O5tcQ reduce the noise] '''if''' the saw uses a belt
-* hook up a [[Shop Vac|shop vac]] to ''reduce'' dust
-* never operate the saw if you are in the CoMakingSpace by yourself
-* make sure the table is standing safely and securely - anti-slide mats may help
-== Maintenance ==
+Next, heat up the soldering iron to around 300°C. When the solder melts by touching to tip, the iron is ready for use. <br/>
-The blade should be sharpened or replaced when it becomes dull, otherwise using it is very dangerous! Tell a [[manager]] if you are noticing any problems, e.g. increased force required to push your workpieces or poor quality cuts.
+Try not to melt the solder directly on the tip but rather heat your components with the soldering iron and then apply solder to the parts. This will result in an optimal flow of the liquid solder and avoid "cold solder joints". If the joint is shining like a polished piece of metal then the soldering was successful and a reliable electrical connection was made. <br/>
+Clean the tip afterwards with the brass wool and/or the wet sponge that's usually integrated into the iron's "station".
-Decreased cutting ability can also result from dirt buildup - here are some [http://www.instructables.com/id/How-to-Clean-a-Table-Saw-Blade/ cleaning instructions].
+'''Ask a [[Tutors|tutor]]''' if you have any questions or want an [[Soldering Iron Introduction|introduction into soldering]]. This [http://www.instructables.com/id/The-Ultimate-Wire-Soldering-Guide-for-Beginners/ video tutorial on splicing and soldering wires] or the mikrocontroller.net page [https://www.mikrocontroller.net/articles/L%C3%B6ten ''"Löten" (DE)''] may also be interesting.
-=== Repairs & Upgrades ===
+== Safety ==
-* fall 2018 (after approx. one year of use):
+* Please be careful while handling a soldering iron as it gets '''very hot'''! Mind your surroundings and other people to avoid injuries.
-** pin holding the cam lever of the parallel fence sometimes came loose - {{£}} put an M3 screw with a [[Lock Nut|lock nut]] through it to keep it in place
+* '''Avoid breathing in the smoke''' forming after melting solder. It isn't as much the lead vapor but the flux which is quite unhealthy when inhaled. If you plan on soldering for an extended amount of time consider '''using an extraction fan''' to reduce exposure.
-** threaded insert to secure the parallel fence in the front became loose, had to be replaced with a [[T-Nut|T-nut]] that [[User:SebastianBillaudelle|Sebastian]] cut to size
+* Be aware to '''wash your hands after''' handling electronic components as the flux and the lead in the solder are '''toxic''' when absorbed through mucous membranes. Avoid touching your face or food while soldering to minimize contact.
-** dust extraction hose sometimes came off - [[User:Moritz|Moritz]] secured it with [[Zip Ties|zip ties]] so it hopefully won't happen again
+<br clear="all">
-* March 2019: broken pin in the height adjustment handwheel replaced with a [[Blind Rivet|blind rivet]] pin ([[User:Moritz|Moritz]] and {{£}})
-== Fences & Jigs ==
-Two aluminum fences come with the saw and can be mounted as a parallel ("rip") and a miter ("crosscut") fence.
-[[Jigs]] we would like to add are helpers for safer and more accurate use, e.g. table saw sleds.
-=== Push Sticks ===
+<!--  NOTE: The following block "imports" content from separate pages - please don't change the code! To edit the actual information, please go back and click "edit" next to the section headline you are interested in :-)  -->
-A simple plastic [[Push Sticks|push stick]] came with the saw, but it's easy to make custom ones that may be more suitable for your project. If anything about the cut you're trying to make does not feel right, use a different push stick or ask someone with more experience!
+{{#ask:
+ [[MachineType::Soldering Iron]]
-Depending on the size of your workpiece, [[Push Blocks|push blocks]] may also work.
+ |order=descending
+ |format=embedded
-== Saw Blade ==
+ |embedonly=yes
-Same general options as for [[Circular Saw|circular saw]] or [[Chop Saw|chop saw]].
+}}
+==Accessories==
+{{#ask:
+ [[Category:Tools]] [[Used With::Soldering Irons]]
+ |order=descending
+ |format=embedded
+ |embedonly=yes
+}}
-[[Category:Power Tools]]
+[[Category:Electronics]]
-[[Category:Saws]]
-[[Category:Woodworking]]