Einhell BT-GW 150: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
MIG/MAG welding machine by Einhell. | |||
{{MachineInfoBox|machine name=welding machine|german=Schutzschweißgerät|image=Schutzgas-Schweissgerät BT-GW 150.jpg|synonyms=Schutzschweißgerät|status=commissioning|material=Metal|location= | To be used with Argon for [https://www.twi-global.com/technical-knowledge/job-knowledge/mig-welding-004 MIG] welding or CO2 for [https://www.uti.edu/blog/welding/gmaw-mag-welding MAG] welding. | ||
{{MachineInfoBox|machine name=welding machine|german=Schutzschweißgerät|image=Schutzgas-Schweissgerät BT-GW 150.jpg|synonyms=Schutzschweißgerät|status=commissioning|material=Metal|similar=https://wiki.comakingspace.de/Welding_Transformer|location=Metal Workshop|access=[[Introduction::Arc_Welding_Introduction]]|manual=https://assets.einhell.com/manuals-pdf/900_177283/BT-GW%20150.pdf}}{{Commissioning}} | |||
[[File:Welding pressure gauge.jpg|thumb]] | [[File:Welding pressure gauge.jpg|thumb]] | ||
[[File:BT-GW 150 Front.jpg|thumb]] | |||
== The gas setup == | |||
The inert gas (Argon) or active gas (CO2) is at ~200 bar if the gas cylinder is full. A pressure reducer reduces this pressure. It also limits the flow rate of the gas. Notice the flow rate has a scale for each gas. 11l/min is a good starting value for the flow rate. Both the bottle valve and the second valve have to be open for gas to flow. Turn the regulation knob to adjust the flow rate. | |||
== The welding machine == | |||
The welding machine has a setting for the welding current , as well as a setting for the wire feed rate. It uses wire of 0.6mm or 0.8mm diameter. The wire spools can have up to 5 kg. | |||
Before welding the metal workpiece, you need to gound it using the grounding clamp. Read the [https://wiki.comakingspace.de/Arc_Welding_Introduction2 welding introduction] on what else precautions you might need to take. | |||
The welding gun has a trigger. If it is pulled, gas is released from it, then wire is fed at a constant rate. The gas prevents the hot metal from exidizing. As soon as the wire gets close to the grounded workng peace a light arc is formed which melts the wire and the workpiece. | |||
Turning the welding current too high might trip the circuit breaker. just turn the current down and reset the circuit breaker. | |||
== Suggested reading == | |||
Know the difference between the different [http://w welding methods] | |||
[[File:BT-GW 150 Front.jpg|thumb|THe settings of the machine]] | |||
Revision as of 19:23, 18 March 2024
MIG/MAG welding machine by Einhell.
To be used with Argon for MIG welding or CO2 for MAG welding.
| MachineInfoBox welding machine | |
|---|---|
| |
| Synonyms: | Schutzschweißgerät |
| Material: | Metal |
| Location: | Metal Workshop |
| Access Requirements: | |
| Status: | commissioning |
| Manual: | https://assets.einhell.com/manuals-pdf/900_177283/BT-GW%20150.pdf |
| Tutors: | |
| Similar (More or Less): | https://wiki.comakingspace.de/Welding_Transformer |
This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!
| Task | comment | Status |
|---|---|---|
| Name the tool: | - | pending |
| Take a picture | - | pending |
| Find the manual as PDF | needed for all machines - add a link to the InfoBox or comment where you could not find it | pending |
| Documentation | this page, status: in commissioning | pending |
| Print QR-Code | use the wikicrawler | pending |
| Introduction | - | pending |
| Security Check | to be done or witnessed by a manager | pending |
| Test | to be done or witnessed by a manager | pending |
| tool's name, owner and approx. value | provide to Patrick for inventorization | pending |
| Last step: make it available | physically and in the wiki - then delete this template | pending |
The gas setup
The inert gas (Argon) or active gas (CO2) is at ~200 bar if the gas cylinder is full. A pressure reducer reduces this pressure. It also limits the flow rate of the gas. Notice the flow rate has a scale for each gas. 11l/min is a good starting value for the flow rate. Both the bottle valve and the second valve have to be open for gas to flow. Turn the regulation knob to adjust the flow rate.
The welding machine
The welding machine has a setting for the welding current , as well as a setting for the wire feed rate. It uses wire of 0.6mm or 0.8mm diameter. The wire spools can have up to 5 kg.
Before welding the metal workpiece, you need to gound it using the grounding clamp. Read the welding introduction on what else precautions you might need to take.
The welding gun has a trigger. If it is pulled, gas is released from it, then wire is fed at a constant rate. The gas prevents the hot metal from exidizing. As soon as the wire gets close to the grounded workng peace a light arc is formed which melts the wire and the workpiece.
Turning the welding current too high might trip the circuit breaker. just turn the current down and reset the circuit breaker.
Suggested reading
Know the difference between the different welding methods
