Reciprocating Saw Introduction: Difference between revisions
From CoMakingSpace Wiki
(integrated Jigsaw Introduction; →Safety: turned into table) |
m (tutor Philip) |
||
| (7 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
This is the content required for an introduction to our [[Introduction for::Reciprocating Saw| reciprocating saw]] and [[Introduction for::jigsaws]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | |||
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Lukas|Lukas]], [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:Sebastian|Sebastian]], [[Tutor::User:Utis|Utis]], [[Tutor::User:Baumphil|Philip]] | |||
Let's begin! First off, make sure you have read the corresponding tool's manual: | Let's begin! First off, make sure you have read the corresponding tool's manual: | ||
| Line 9: | Line 9: | ||
== Safety == | == Safety == | ||
[[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]] | [[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]][[File:Protection - hearing.svg|50x50px]] | ||
'' | ''Additional protection for toxic or allergenic woods (especially hardwoods, e.g. beech and oak - see "[[dust]]") or for certain surface finishes or chemicals:'' [[File:Protection - breathing.svg|50x50px]] | ||
{| class="wikitable" | {| class="wikitable" | ||
| Line 18: | Line 18: | ||
|- | |- | ||
| sharp oscillating blade - possible kickback || | | sharp oscillating blade - possible kickback || | ||
* | * you MUST NOT turn on the saw when the blade is already touching something (e.g. the workpiece) | ||
* | * you MUST let the baseplate touch the workpiece before starting to cut | ||
* blind cut: leave the sawblade in the cut until it has stopped | * blind cut: leave the sawblade in the cut until it has stopped | ||
* through cut: make sure the blade has stopped moving before putting the saw back on the table | * through cut: make sure the blade has stopped moving before putting the saw back on the table | ||
* make sure the blade path is free and you won't cut into the table or similar | * you MUST make sure the blade path is free and you won't cut into the table or similar | ||
* make sure the blade is long enough so that it can reach through the material when fully retracted (too short a blade relative to the material being cut will cause dangerous kickback) | * you MUST make sure the blade is long enough so that it can reach through the material when fully retracted (too short a blade relative to the material being cut will cause dangerous kickback) | ||
* | * you MUST make sure there are no obstacles such as nails in your path before starting a cut | ||
* secure the workpiece with [[clamps]] so nothing shifts and nothing large falls down once the cut is made | * you MUST secure the workpiece with [[clamps]] so nothing shifts and nothing large falls down once the cut is made | ||
|- | |- | ||
| generates dust and small chips || | | generates dust and small chips || | ||
* wear [[goggles]] | * you MUST wear [[goggles]] | ||
* hook up the [[Shop Vac|shop vac]] (and deactivate the "dust blow" function of the saw, if available) | * you SHOULD hook up the [[Shop Vac|shop vac]] (and deactivate the "dust blow" function of the saw, if available) | ||
* if your workpiece is contaminated with chemicals or made from hard woods like beech ''(Buche)'' or oak ''(Eiche)'', you SHOULD use a [[Dust Mask|dust mask]] | |||
|- | |- | ||
| generates noise || wear [[Ear Defenders|ear defenders]] | | generates noise || | ||
* you MUST wear [[Ear Defenders|ear defenders]] | |||
|- | |- | ||
| [[File:Danger_-_sudden_start.svg|left|50px]] no prevention of turning on after loss & restoration of power (''keine Anlaufsicherung'') || make sure the locking | | | ||
the blade can get very hot | |||
* remains hot for a while after using | |||
|| when you see smoke, immediately stop and inspect the saw - the blade might be dull or jammed in the workpiece. Also do not stay in the same place for too long! | |||
|- | |||
| [[File:Danger_-_sudden_start.svg|left|50px]] no prevention of turning on after loss & restoration of power (''keine Anlaufsicherung'') || | |||
* you MUST make sure the locking button is "off" before plugging the saw in (the trigger should move freely) | |||
|} | |} | ||
== Demonstration == | == Demonstration == | ||
Latest revision as of 20:52, 9 October 2024
This is the content required for an introduction to our reciprocating saw and jigsaws - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
If you need this introduction, please reach out to the following tutors: Lukas, Patrick, Johannes, Luzian, Sebastian, Utis, Philip
Let's begin! First off, make sure you have read the corresponding tool's manual:
Safety
Additional protection for toxic or allergenic woods (especially hardwoods, e.g. beech and oak - see "dust") or for certain surface finishes or chemicals: 
| Dangers | Precautions |
|---|---|
| sharp oscillating blade - possible kickback |
|
| generates dust and small chips | |
| generates noise |
|
|
the blade can get very hot
|
when you see smoke, immediately stop and inspect the saw - the blade might be dull or jammed in the workpiece. Also do not stay in the same place for too long! |
 |
|
Demonstration
During the introduction, the tutor will show you the following:
- inserting/removing saw blades
- choosing and changing the pendulum or orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)
Besides these safety notes, you should know which type of blade is suitable for the material you want to cut!
