Project:Pizza Peel: Difference between revisions

Latest revision as of 21:55, 7 March 2020

ProjectInfoBox Simple Pizza Peels

Status:	75 % done
Release Date:	June 2018
Initiator:	Lukas
Materials Used:	multi-ply
Tools Used:	table saw, scroll saw, rasps, sandpaper
Approx. Cost:	10 €

I wanted to make two simple pizza peels out of birch multi-ply.

This was a nice chance to try spiral-toothed scroll saw blades as the boards required for this project would be too large for the saw if cut with regular blades.

Design

Based on a peel and stone that I already have and the box it should fit in, these are the desired measurements:

thickness: ~~5 mm~~ 6 mm (was available at the Space)
handle: approx. 12 × 4 cm
surface: approx. 35 × 30 cm (wider than long)
front edge: chamfered for 12 mm

Make

cut: table saw for width, scroll saw for handle & curved shoulders
chamfer: used a rasp to remove most of the unwanted material at the front edge
sand: old sanding disc for cleaning up the cut, sanding block to finish the chamfer

→ only finished one so far, perhaps the chamfer needs to be adjusted due to the thicker material that was used - to be continued after some test pizzas

major steps
transferring the design
cutting on the scroll saw
all cut out
smoothing the edges with an old sanding disc
a rasp forms the chamfer...
...and a sanding block smooths it out
(probably) finished piece

@@ Line 1: / Line 1: @@
-I want to make two simple pizza peels out of birch [[multi-ply]].
+{{ProjectInfoBox
+|project title=Simple Pizza Peels
+|image=pizzapeel-0.JPG
+|status=75 % done
+|date=June 2018
+|initiator={{£}}
+|team=
+|materials=[[multi-ply]]
+|tools=[[Table Saw|table saw]], [[Scroll Saw|scroll saw]], [[rasps]], [[sandpaper]]
+|software=
+|cost=10 €
+}}
+I wanted to make two simple pizza peels out of birch [[multi-ply]].
-This should be a nice chance to try spiral-toothed [[Scroll Saw|scroll saw]] blades.
+This was a nice chance to try spiral-toothed [[Scroll Saw|scroll saw]] blades as the boards required for this project would be too large for the saw if cut with regular blades.
 == Design ==
 Based on a peel and stone that I already have and the box it should fit in, these are the desired measurements:
-* thickness: 5 mm
+* thickness: <strike>5 mm</strike> 6 mm ''(was available at the Space)''
 * handle: approx. 12{{x}}4 cm
 * surface: approx. 35{{x}}30 cm (wider than long)
@@ Line 11: / Line 23: @@
 == Make ==
- - TBD -
+# cut: [[Table Saw|table saw]] for width, [[Scroll Saw|scroll saw]] for handle & curved shoulders
-# cut
+# chamfer: used a [[rasp]] to remove most of the unwanted material at the front edge
-# chamfer
+# sand: old [[Sanding Discs|sanding disc]] for cleaning up the cut, [[Sanding Block|sanding block]] to finish the chamfer
-# sand
-<!-- add later:
+&rarr; only finished one so far, perhaps the chamfer needs to be adjusted due to the thicker material that was used - to be continued after some test pizzas
+<gallery mode=packed-hover heights=250 caption="major steps">
+File: pizzapeel-1.JPG|transferring the design
+File: pizzapeel-2.JPG|cutting on the [[Scroll Saw|scroll saw]]
+File: pizzapeel-3.JPG|all cut out
+File: pizzapeel-4.JPG|smoothing the edges with an old [[Sanding Disc|sanding disc]]
+File: pizzapeel-5.JPG|a [[rasp]] forms the chamfer...
+File: pizzapeel-6.JPG|...and a [[Sanding Block|sanding block]] smooths it out
+File: pizzapeel-0.JPG|(probably) finished piece
+</gallery>
+[[Category:Cooking]]
 [[Category:Quick Projects]]
-[[Category:Woodworking]] -->
+[[Category:Woodworking]]