Handheld Router Introduction: Difference between revisions
(added waiting list) |
m (typo) |
||
(12 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
This is the content required for an introduction to our [[routers]] | This is the content required for an introduction to our [[Introduction for::Handheld Routers|handheld routers]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | ||
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Lukas|Lukas]], [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:Keno|Keno]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Utis|Utis]] | |||
First off, make sure you have read the tool's | Please be aware that the [[CNC Router Introduction|CNC router introduction]] and [[Router Table Introduction|router table introduction]] (as of 2020-4-15) are '''separate''' but require this one as a background. | ||
First off, make sure you have read the tool's manual, if available (it should be linked from its InfoBox). | |||
== Safety == | == Safety == | ||
[[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]] [[File:Protection - hearing.svg|50px]] [[File:Protection - no gloves.svg|50px]] | |||
= | ''a [[Dust Mask|dust mask]] could be necessary depending on your material'' | ||
{| class="wikitable" | |||
|- | |||
! Dangers !! Precautions | |||
|- | |||
| [[File:Danger_-_draw-in.svg|left|50px]] exposed & rapidly spinning [[Router Bit|router bit]] | |||
::* will keep spinning for a few seconds after the tool is turned off | |||
|| | |||
* wear [[Personal Protection|personal protection]] but '''not''' [[gloves]], they could get caught! | * wear [[Personal Protection|personal protection]] but '''not''' [[gloves]], they could get caught! | ||
* stay clear of the bit when in operation (both hands on the handles!) | * stay clear of the bit when in operation (both hands on the handles!) | ||
* unplug the router when changing a bit or touching the collet for any other reason | * unplug the router when changing a bit or touching the collet for any other reason | ||
|- | |||
| the bit can bite into the workpiece and cause kickback if the wrong feed direction or pressure is applied || | |||
* always keep at least one of the two columns over your workpiece, that way the base should be stable and won't tip over | * always keep at least one of the two columns over your workpiece, that way the base should be stable and won't tip over | ||
* do not let the bit touch the workpiece before it has reached its full speed | * do not let the bit touch the workpiece before it has reached its full speed | ||
* be prepared for sudden movements of the workpiece and make sure it is properly secured | * be prepared for sudden movements of the workpiece and make sure it is properly secured | ||
** small workpieces (smaller than half the tool's base in width OR length) are not suitable for the | ** small workpieces (smaller than half the tool's base in width OR length) are not suitable for handheld routing, but should be taken to the [[Router Table|router table]] | ||
* always check whether the tool movement you are planning is possible '''before''' turning it on - adjust depth if necessary | * always check whether the tool movement you are planning is possible '''before''' turning it on - adjust depth if necessary | ||
|- | |||
| flying splinters and dust || | |||
* hook up a [[Shop Vac|shop vac]] to extract (most of) the dust at the source | |||
* make sure there is nobody nearby who might be surprised by a piece of shrapnel flying their way! | * make sure there is nobody nearby who might be surprised by a piece of shrapnel flying their way! | ||
* | |- | ||
| | |||
the bit can get extremely hot | |||
* can potentially set the sawdust on fire | |||
* remains hot for a while after using | |||
|| when you see smoke, immediately stop and re-think your tool settings - it might be spinning too fast or you could be feeding too slow! Are you sure your bit is sharp? | |||
|} | |||
==== Feed Direction ==== | ==== Feed Direction ==== | ||
Line 35: | Line 45: | ||
As mentioned in the video as well, there are only a few situations where you might want to try a "climb" cut once you are sufficiently experienced with this tool. When you do attempt climb cuts, be aware that it can cause kickback to the router and the workpiece! Only take shallow passes to maintain control. | As mentioned in the video as well, there are only a few situations where you might want to try a "climb" cut once you are sufficiently experienced with this tool. When you do attempt climb cuts, be aware that it can cause kickback to the router and the workpiece! Only take shallow passes to maintain control. | ||
Caution: grooves ''in'' a workpiece are usually "outside" work (because the parallel fence will reference the ''outside'' of the workpiece), so you'll want to go anti-clockwise! There is no dangerous kickback in grooves, but choosing the wrong direction can easily cause your fence to become pushed out of line - resulting in a wavy cut.<sup> [https://www.youtube.com/watch?v=5Qqimqo-ohU&t=18m02s video demo]</sup> | |||
A clever trick to determine the push direction is to '''use your right hand with extended thumb and index finger as an indicator''': when the back of your hand points where the top of the router is (usually up, but down in a [[Router Table|router table]]), your index finger shows the correct feed direction to work on the edge that your thumb is touching.<sup> [http://www.holzwerken.net/Blog/Guido-Henn/So-fraesen-Sie-immer-sicher-im-Gegenlauf]</sup> | |||
==== [[Feedrate]] ==== | ==== [[Feedrate]] ==== | ||
Line 45: | Line 59: | ||
* inserting a bit | * inserting a bit | ||
** unplug the router | ** unplug the router | ||
** choose the proper collet that matches the bit's shaft diameter (6 or 8 mm) | ** choose the proper collet that matches the bit's shaft diameter (usually 6 or 8 mm) | ||
** insert at least 20 mm of the bit's shaft | ** insert at least 20 mm of the bit's shaft | ||
** check proper fit and balance before turning the motor on | ** check proper fit and balance before turning the motor on | ||
Line 51: | Line 65: | ||
== Suggested Reading == | == Suggested Reading == | ||
Please make yourself familiar with [[Router Bits|router bits]]! | |||
For tips and tricks read the book "Woodworking with the Router" (available at the space). Tips for choosing the proper feed direction can be found on page 37ff. | For tips and tricks read the book "Woodworking with the Router" (available at the space). Tips for choosing the proper feed direction can be found on page 37ff. | ||
{{Waiting List}} | {{Waiting List}} | ||
[[Category:Introductions]] | [[Category:Introductions]] |
Latest revision as of 22:53, 28 February 2024
This is the content required for an introduction to our handheld routers - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
If you need this introduction, please reach out to the following tutors: Lukas, Martin, Luzian, Keno, Johannes, Patrick, Utis
Please be aware that the CNC router introduction and router table introduction (as of 2020-4-15) are separate but require this one as a background.
First off, make sure you have read the tool's manual, if available (it should be linked from its InfoBox).
Safety
a dust mask could be necessary depending on your material
Dangers | Precautions |
---|---|
exposed & rapidly spinning router bit
|
|
the bit can bite into the workpiece and cause kickback if the wrong feed direction or pressure is applied |
|
flying splinters and dust |
|
the bit can get extremely hot
|
when you see smoke, immediately stop and re-think your tool settings - it might be spinning too fast or you could be feeding too slow! Are you sure your bit is sharp? |
Feed Direction
The standard direction is the "push" cut, i.e. against the direction the bit would pull the router if you let go. In short, you need to move the router counter-clockwise around the outside of a workpiece and clockwise for inside work (holes, recesses). It is probably more clear after watching this video tutorial!
As mentioned in the video as well, there are only a few situations where you might want to try a "climb" cut once you are sufficiently experienced with this tool. When you do attempt climb cuts, be aware that it can cause kickback to the router and the workpiece! Only take shallow passes to maintain control.
Caution: grooves in a workpiece are usually "outside" work (because the parallel fence will reference the outside of the workpiece), so you'll want to go anti-clockwise! There is no dangerous kickback in grooves, but choosing the wrong direction can easily cause your fence to become pushed out of line - resulting in a wavy cut. video demo
A clever trick to determine the push direction is to use your right hand with extended thumb and index finger as an indicator: when the back of your hand points where the top of the router is (usually up, but down in a router table), your index finger shows the correct feed direction to work on the edge that your thumb is touching. [1]
Feedrate
The proper combination of rotation speed and tool advancement is determined by your bit and material.
- be cautions not to remove too much material at a time - several passes are usually necessary if you want to go deep
- going too slow can cause the wood to burn, going to fast can cause the wood to splinter and even damage the bit
Demonstration
The tutor will show you these steps in detail:
- inserting a bit
- unplug the router
- choose the proper collet that matches the bit's shaft diameter (usually 6 or 8 mm)
- insert at least 20 mm of the bit's shaft
- check proper fit and balance before turning the motor on
- never tighten the collet without a bit inserted!
Suggested Reading
Please make yourself familiar with router bits!
For tips and tricks read the book "Woodworking with the Router" (available at the space). Tips for choosing the proper feed direction can be found on page 37ff.
Waiting List
This introduction takes longer than many others and usually can't be done spontaneously during regular opening times. If you would like to receive it, please add yourself to >> this list << and we will find a good time once a few members are on it!