Biscuit Joiner: Difference between revisions
From CoMakingSpace Wiki
NitramLegov (talk | contribs) (Format cleanup :)) |
NitramLegov (talk | contribs) m (Moving to machine specific page) |
||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
A biscuit joiner is very useful for panel glue-ups, where the evenly placed wooden "[[biscuits]]" ''(Flachdübel)'' make sure the individual boards' surfaces stay aligned. This is especially useful if your [[clamps]] would push the boards in different directions, e.g. when the outer edges are not parallel to the one you want to glue. | |||
[[File:Biscuits explained.svg|thumb|left|biscuits may help direct the clamping force how you intended]] | |||
The biscuits are made of compressed wood fibers and are supposed to swell up when moistened with [[Wood Glue|wood glue]], resulting in a tighter fit inside their grooves. However, keep in mind that they are only meant to help with alignment and the actual strength of the glue joint will depend on the edge quality of the board! Using a [[jointer]] is always a good first step. | |||
<br clear=left> | |||
== Example == | == Example == | ||
In | In this example, two small boards have been used as a test / demonstration for the biscuit joiner: | ||
File:Biscuit joiner | <gallery mode=packed> | ||
File:Biscuit joiner aligned side.jpg| | File:Biscuit joiner boards side by side.jpg|Four grooves made with the joiner are visible, one has a biscuit inserted. | ||
File:Biscuit joiner aligned top.jpg|Imagine lots of [[Wood Glue|wood glue]] on the flat side and inside the grooves... | |||
</gallery><br clear="all"> | File:Biscuit joiner aligned side.jpg|This picture shows how the biscuit helps with keeping the boards flat during assembly (ignore the grooves in the foreground). | ||
</gallery> | |||
<br clear="all" /> | |||
{{ | <!-- NOTE: The following block "imports" content from separate pages - please don't change the code! To edit the actual information, please go back and click "edit" next to the section headline you are interested in :-) --> | ||
{{#ask: | |||
[[MachineType::Biscuit Joiner]] | |||
|order=ascending | |||
|format=embedded | |||
|embedonly=yes | |||
| | |||
| | |||
| | |||
}} | }} | ||
[[Category:Joinery]] | [[Category:Joinery]] | ||
[[Category:Woodworking]] | [[Category:Woodworking]] | ||
Latest revision as of 22:00, 16 October 2022
A biscuit joiner is very useful for panel glue-ups, where the evenly placed wooden "biscuits" (Flachdübel) make sure the individual boards' surfaces stay aligned. This is especially useful if your clamps would push the boards in different directions, e.g. when the outer edges are not parallel to the one you want to glue.
The biscuits are made of compressed wood fibers and are supposed to swell up when moistened with wood glue, resulting in a tighter fit inside their grooves. However, keep in mind that they are only meant to help with alignment and the actual strength of the glue joint will depend on the edge quality of the board! Using a jointer is always a good first step.
Example
In this example, two small boards have been used as a test / demonstration for the biscuit joiner:
Four grooves made with the joiner are visible, one has a biscuit inserted.
Imagine lots of wood glue on the flat side and inside the grooves...
This picture shows how the biscuit helps with keeping the boards flat during assembly (ignore the grooves in the foreground).
Toolson PRO-DF 860
| MachineInfoBox Toolson PRO-DF 860 | |
|---|---|
| |
| Synonyms: | DE: Flachdübelfräsmaschine, Flachdübelfräse, Handschlitzfräse, Nutfräse, Lamellofräse |
| Type: | Biscuit Joiner |
| Material: | wood |
| Used with: | biscuits, wood glue |
| Location: | Saw Station |
| Access Requirements: | Biscuit Joiner Introduction |
| Status: | Working |
| Manual: | media.bahag.com |
| Tutors: | Lukas Pakue |
| Similar (More or Less): | "Domino" joiner |
As mentioned in the Plenum, Sebastian B. brought in a biscuit joiner.
