Uploads by Lukas
From CoMakingSpace Wiki
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 20:20, 23 October 2018 | Screenshot - Inkscape.PNG (file) |  |
192 KB | screenshot of a typical Inkscape project (in this case: drawing wiki illustrations of woodturning tools) | 1 |
| 17:34, 23 October 2018 | Router table feed direction.png (file) |  |
14 KB | Basic schematic of the proper feed direction on a router table, resulting in safe climb cuts whichever side of the bit you are working on. Drawn in Inkscape, also see animated version: [[:File:Router table feed direction animation... | 1 |
| 17:44, 22 October 2018 | Westfalia router table off center.JPG (file) |  |
501 KB | When we got the Westfalia router table, the router was mounted too far to the front so the bit would be off center - not that the scale on this simple table would have been too accurate anyway, but something we will fix nevertheless! | 1 |
| 17:41, 22 October 2018 | Westfalia router table fence-top.JPG (file) |  |
475 KB | In addition to the fence, you should use additional guides on the router table whenever you can - shown here is a rigid top guide ''almost'' touching the workpiece, featherboards can actually press on it and are even safer! | 1 |
| 17:37, 22 October 2018 | Westfalia router table fence-X.JPG (file) |  |
478 KB | The screw knob marked "X" should be left alone unless you really need it - it lets you move the left part of the fence back and forward on its own; for the majority of jobs on the router table (if not all) you want the fence to be perf... | 1 |
| 17:31, 22 October 2018 | Westfalia router table dust ports.JPG (file) |  |
441 KB | there are two places where you can connect a shop vac to the Westfalia router table: top (green) - most useful for edge work - or bottom (black) - most useful for grooves | 1 |
| 21:45, 30 September 2018 | File handles 12.JPG (file) |  |
561 KB | a self-made file handle next to an "original" one | 1 |
| 21:44, 30 September 2018 | File handles 11.png (file) |  |
2 MB | do NOT use a hammer to drive the file into a (self-made) file handle - the hardened steel could break - but instead push it in as far as you can and then hit the workbench surface with the handle's end a few times photo edited... | 1 |
| 21:29, 30 September 2018 | File handles 10.JPG (file) |  |
395 KB | for drilling the hole in a self-made file handle, a stepped approach may be best but a first attempt with a drill bit about half the diameter of the thickest file shaft part was also successful | 1 |
| 21:26, 30 September 2018 | File handles 09.JPG (file) |  |
449 KB | taking a self-made file handle off the wood lathe: you could do ''some'' of the work with a parting tool, but using a sharp saw with the lathe turned off is the safest way | 1 |
| 21:23, 30 September 2018 | File handles 08.JPG (file) |  |
337 KB | Sanding on the wood lathe is awesome! Here, a self-made file handle gets its final touch | 1 |
| 21:20, 30 September 2018 | File handles 07.JPG (file) |  |
495 KB | now it really looks like a self-made file handle: a groove has been formed with a skew chisel where it will feel comfortable | 1 |
| 20:42, 30 September 2018 | File handles 06.JPG (file) |  |
452 KB | the blank for a self-made file handle is taking shape after some further smoothing with a skew chisel | 1 |
| 20:35, 30 September 2018 | File handles 05.JPG (file) |  |
429 KB | a self-made file handle in progress: after roughing out a cylinder, a parting tool is used to get the proper diameter for a ferrule | 1 |
| 20:33, 30 September 2018 | File handles 04.JPG (file) |  |
443 KB | turning blank for a self-made file handle set up between centers on the wood lathe | 1 |
| 19:16, 30 September 2018 | File handles 03.JPG (file) |  |
509 KB | cutting a turning blank for a self-made file handle with a Japanese saw | 1 |
| 19:13, 30 September 2018 | File handles 02.JPG (file) |  |
446 KB | measuring the ferrule for a self-made file handle with digital calipers - here you can truly appreciate that they always take an identical measurement for inside and outside with their two pairs of probes! | 1 |
| 19:09, 30 September 2018 | File handles 01.jpg (file) |  |
951 KB | cutting a ferrule for a self-made file handle from steel pipe with a hacksaw | 1 |
| 18:04, 30 September 2018 | File handles cover.JPG (file) |  |
459 KB | a self-made file handle still on the wood lathe | 1 |
| 20:26, 28 September 2018 | Woodturning scraper.svg (file) |  |
7 KB | Sketch to illustrate the geometry of a woodturning scraper (b: bevel angle). Drawn with Inkscape. | 1 |
| 20:05, 28 September 2018 | Skew chisel.svg (file) |  |
9 KB | Sketch to illustrate the geometry of a skew chisel (b: bevel angle, s: skew angle). Drawn with Inkscape. | 1 |
| 19:40, 28 September 2018 | Spindle gouge.svg (file) |  |
8 KB | Sketch to illustrate the geometry of a spindle gouge (b: bevel angle). Drawn with Inkscape. | 1 |
| 19:31, 28 September 2018 | Roughing gouge.svg (file) |  |
7 KB | Sketch to illustrate the geometry of a roughing gouge (b: bevel angle). Drawn with Inkscape. | 1 |
| 19:26, 28 September 2018 | Fingernail bowl gouge.svg (file) |  |
9 KB | square version | 2 |
| 19:25, 28 September 2018 | Bowl gouge.svg (file) |  |
9 KB | square version | 2 |
| 21:33, 27 September 2018 | VHS table 08.jpg (file) |  |
392 KB | both VHS couch table legs finished and in front of their couch | 1 |
| 21:30, 27 September 2018 | VHS table 07.JPG (file) |  |
349 KB | the top board of a VHS couch table leg is made of two carefully laid out pieces to give a bit of extra stability from the inside and let each leg double as a side table when the large top is removed | 1 |
| 21:27, 27 September 2018 | VHS table 06.jpg (file) |  |
435 KB | finished tape assembly for a VHS couch table leg | 1 |
| 21:25, 27 September 2018 | VHS table 05.JPG (file) |  |
447 KB | to connect the different layers of VHS couch table legs with rivets, makeshift brackets out of some surplus tapes proved efficient (and nearly invisible in the end) | 1 |
| 21:21, 27 September 2018 | VHS table 04.JPG (file) |  |
483 KB | Fifth and most complicated layer of a VHS couch table leg: two sets of two sandwiched tapes and four single ones standing on their short edge, forming something like a rectangle. This weird arrangement was necessary to gain... | 1 |
| 21:20, 27 September 2018 | VHS table 03.JPG (file) |  |
506 KB | third and fourth layer of a VHS couch table leg: two tapes lying flat (they will be hidden later, don't choose your favorite ones) on top of another ring as was also used for the second layer | 1 |
| 21:18, 27 September 2018 | VHS table 02.JPG (file) |  |
558 KB | the second layer of a VHS couch table leg: four tapes on their long edge (labels nicely visible!) | 1 |
| 21:18, 27 September 2018 | VHS table 01.JPG (file) |  |
507 KB | assembling four VHS tapes in a square with a rivet gun - this will be the base of a couch table leg | 1 |
| 17:43, 20 September 2018 | Coming soon.svg (file) |  |
3 KB | placeholder for missing project photos, e.g. on your user page quickly created with Inkscape. | 1 |
| 18:54, 12 September 2018 | Tacklife PAH01D.JPG (file) |  |
4.09 MB | Tacklife PAH01D welding helmet sitting on its bag | 1 |
| 18:10, 5 August 2018 | Sticky, stringy.jpg (file) |  |
671 KB | pulling on some old adhesives holding a machine's feet | 1 |
| 02:15, 5 August 2018 | Alpha Tools WS 960-125.jpg (file) |  |
839 KB | Alpha Tools WS 960/125 disc grinder | 1 |
| 01:46, 5 August 2018 | M3 to M12 taps.jpg (file) |  |
433 KB | M3 to M12 set of three-stage taps | 1 |
| 01:44, 5 August 2018 | M3 to M12 dies.jpg (file) |  |
382 KB | set of M3 to M12 dies with their box and holder | 1 |
| 01:41, 5 August 2018 | Taps and dies.JPG (file) |  |
518 KB | a selection of our taps and dies and their respective holders | 1 |
| 22:52, 1 August 2018 | Paper cutter.JPG (file) |  |
349 KB | our 2 in 1 paper cutter (with its knife side in use) | 1 |
| 20:15, 1 August 2018 | Precious plastic shredder parts.jpg (file) |  |
412 KB | laser cut parts for our Precious Plastic shredder photo by Flor | 1 |
| 18:48, 20 July 2018 | Drying timber variety.JPG (file) |  |
430 KB | a bunch of logs (cherry and ash are in there, not sure about the others right now) treated with different drying methods so they can be used for projects at some point | 1 |
| 18:35, 20 July 2018 | Aq-edge working prototype.JPG (file) |  |
485 KB | first working prototype of Project:Aquarium Edge Illumination | 1 |
| 20:35, 11 July 2018 | Milling styrofoam.JPG (file) |  |
442 KB | a small block of styrofoam gets machined on an "EleksMill" CNC mill | 1 |
| 20:33, 11 July 2018 | EleksMill.jpg (file) |  |
385 KB | Mitja's "EleksMill" CNC mill on a table | 1 |
| 15:07, 10 July 2018 | Corroding magnets.JPG (file) |  |
252 KB | two corroding neodymium magnets next to an intact one (on the left) | 1 |
| 15:03, 8 July 2018 | CNC router.gif (file) |  |
3.74 MB | WorkBee CNC router cutting a circular pocket into a piece of eukalyptus glued laminated timber. GIF created with [https://giphy.com/create/gifmaker Giphy]. | 1 |
| 13:30, 8 July 2018 | CNC workholding - wood screws.JPG (file) |  |
434 KB | driving wood screws through your workpiece and into the spoilboard is a very simple CNC workholding option | 1 |
| 18:40, 5 July 2018 | Pizzapeel-6.JPG (file) |  |
310 KB | sanding the chamfer on a pizza peel with a sanding block to get a smooth surface | 1 |
