Chop Saw Introduction: Difference between revisions

From CoMakingSpace Wiki

(added a part about not cutting metals with a wood-cutting blade)
No edit summary
 
(10 intermediate revisions by 4 users not shown)
Line 1: Line 1:
This is the content required for an introduction to our [[Chop Saw|chop saw]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
This is the content required for an introduction to our [[Introduction for::Chop Saw|chop saw]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
 
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Lukas|Lukas]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Keno|Keno]], [[Tutor::User:Sebastian|Sebastian]], [[Tutor::User:Utis|Utis]], [[Tutor::User:Loewenstein|Jan]], [[Tutor::User:Jakob|Jakob]]


Let's begin! First off, make sure you have read the machine's [https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290462v21_160992A4CT_201808.pdf manual].
Let's begin! First off, make sure you have read the machine's [https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290462v21_160992A4CT_201808.pdf manual].
Line 17: Line 19:
|-
|-
| sawdust and small splinters can fly towards the operator and others ||
| sawdust and small splinters can fly towards the operator and others ||
* hook up a [[Shop Vac|shop vac]], but be aware the dust extraction from our "Herkules" saw is very incomplete
* hook up a [[Shop Vac|shop vac]], but be aware the dust extraction will still be incomplete
** the large saw draws too much power to be connected through the shop vac's on-board outlet, but should be powered from a separate power outlet instead
* wear [[goggles]]
* wear [[goggles]]
* [[Dust Mask|dust mask]]: depending on the material you're cutting
* [[Dust Mask|dust mask]]: depending on the material you're cutting
Line 23: Line 26:
| kickback: workpiece can move during the cut or cause the blade to push itself up ||
| kickback: workpiece can move during the cut or cause the blade to push itself up ||
* clamp your workpiece to the saw's base, if possible
* clamp your workpiece to the saw's base, if possible
** a [[10 Million Dollar Sticks|"10 million dollar stick"]] should be used to hold even smaller pieces
* always cut from front (closer to the user) to the back of the workpiece when using the articulating arm
* always cut from front (closer to the user) to the back of the workpiece when using the articulating arm
* let the saw start '''before''' touching the workpiece
* let the saw start '''before''' touching the workpiece
Line 38: Line 42:
* releasing the blade guard and starting the saw
* releasing the blade guard and starting the saw


{{Waiting List}}
{{#set:
| checklist_title=Chop Saw
| checklist_symbols=M004
| checklist_symbols=M003
| checklist_symbols=M002
| checklist_symbols=M016
| checklist_link=https://wiki.comakingspace.de/index.php?title=Chop_Saw_Introduction
| checklist_before=**Must** check if cut interferes in any way (e.g. fence)
| checklist_before=**Must not** use shop vac outlet (too much startup current)
| checklist_before=**Must not** fix workpiece on both sides at once
| checklist_before=**Should** fix articulating arm if not needed
| checklist_during=**Must** cut from front to back when using articulating arm
| checklist_after=cleanup
}}


[[Category:Introductions]]
[[Category:Introductions]]

Latest revision as of 22:12, 21 February 2024

This is the content required for an introduction to our chop saw - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)

If you need this introduction, please reach out to the following tutors: Patrick, Lukas, Luzian, Martin, Johannes, Keno, Sebastian, Utis, Jan, Jakob

Let's begin! First off, make sure you have read the machine's manual.

Safety

Personal protection: Protection - goggles.svg Protection - hearing.svg

(a dust mask could also be necessary depending on your material)

Dangers Precautions
sharp and rotating exposed blade - will keep spinning for a bit after turning the power off!
  • keep your hands well clear of the blade until it has stopped completely
  • check whether your planned movement is possible before turning the saw on - there are screws that may lock it in several places (see "Demonstration")
sawdust and small splinters can fly towards the operator and others
  • hook up a shop vac, but be aware the dust extraction will still be incomplete
    • the large saw draws too much power to be connected through the shop vac's on-board outlet, but should be powered from a separate power outlet instead
  • wear goggles
  • dust mask: depending on the material you're cutting
kickback: workpiece can move during the cut or cause the blade to push itself up
  • clamp your workpiece to the saw's base, if possible
  • always cut from front (closer to the user) to the back of the workpiece when using the articulating arm
  • let the saw start before touching the workpiece
cutting the incorrect material for a saw blade type
  • only cut wood and plastics with the chop saw in the woodworking area
  • wood-cutting saw blades can easily get caught in workpieces made of metal and can cause serious kickback

Demonstration

The tutor will show you these steps in detail:

  • adjusting the bevel
  • adjusting the rotation
  • setting the depth stop
  • releasing the blade guard and starting the saw

Waiting List

This introduction takes longer than many others and usually can't be done spontaneously during regular opening times. If you would like to receive it, please add yourself to >> this list << and we will find a good time once a few members are on it!

Retrieved from "https://wiki.comakingspace.de/index.php?title=Chop_Saw_Introduction&oldid=16601"