Search results
From CoMakingSpace Wiki
- |tools=[[Laser Cutter|laser cutter]] (engraving; not easily cut) [[Laser Cutting|Laser engraving]] film faced plywood gives a rather dark surface that is not too different5 KB (793 words) - 01:35, 26 February 2020
- ...f cuttable & engravable materials]];<br>[[Laser Cutter#Possible Materials (Engraving Only)|list of only engravable materials]]) * worktable size: 60x90 cm (length x width), engraving a bit smaller3 KB (536 words) - 01:36, 5 November 2022
- == 3D Engraving with a Laser Cutter == The laser cutter we used supported 3D engraving, i.e. engraving at different intensities depending on the darkness of a greyscale image. We6 KB (946 words) - 21:41, 6 October 2017
- ''' laser cutting/engraving '''990 bytes (135 words) - 13:21, 31 August 2017
- * '''Lasercutting''' - Mainly for engraving logos on hardwood build1 KB (195 words) - 20:03, 18 July 2021
- ...ted, 100 % power in a cutting profile is not the same as 100 % power in an engraving profile... <!-- because of different frequencies? --> ...Materials|Forbidden]]''' and '''[[Laser_Cutter#Possible_Materials_(Cutting/Engraving)|Possible Materials]]'''.11 KB (1,488 words) - 02:44, 29 February 2024
- The last step follows the regular preparations for engraving pictures with the laser cutter. The needed settings can be found on the pag ...cutter manufacturer) on [https://www.troteclaser.com/en/applications/stamp-engraving/ stamp rubber and recommended settings]1 KB (234 words) - 07:08, 6 October 2021
- ...r (please reference the list of [[Laser_Cutter#Possible Materials (Cutting/Engraving)|possible materials]] *** set cutting/engraving settings per path5 KB (865 words) - 00:20, 2 March 2024
- ...have not tried this ourselves yet and you should keep in mind that ''laser engraving is basically burning'' which may weaken your piece.2 KB (271 words) - 13:11, 20 June 2021
- ...aterial by following the defined vectors. You can also use this for vector engraving ("marking") by lowering the power. ...ng_Your_Job|simulate the job]] to avoid bad surprises!). Also see "[[Laser Engraving Photos]]" for advice on pre-processing these.12 KB (2,014 words) - 21:08, 9 July 2022
- ...f cuttable & engravable materials]];<br>[[Laser Cutter#Possible Materials (Engraving Only)|list of only engravable materials]]) ** ''raster engraving'' is possible with almost any Windows program that is capable to print8 KB (1,233 words) - 16:19, 5 February 2024
- ...- und Glattleder)''. It can be used for e.g. [[sewing]] and for cutting or engraving with a [[Laser Cutter|laser cutter]].2 KB (386 words) - 02:33, 14 May 2020
- * irreversible: [[Laser Cutter|laser]] engraving with [[Laser Marking Spray|laser marking spray]]6 members (0 subcategories, 0 files) - 01:44, 6 January 2018
- * Upload pictures of fleece engraving4 KB (499 words) - 22:34, 3 August 2023
- **## Engraving the name gives a nice result (cut the border, of course). Just some smoke r4 KB (577 words) - 12:51, 31 May 2024
- * rotary attachment for engraving glasses, bottles etc.5 KB (621 words) - 19:41, 22 April 2024
- **laser cutting/engraving ([[Sebastian]])5 KB (702 words) - 00:31, 11 August 2022
- ** ursprüngliche Planung von [[Keno]] siehe [[Linoprint with Laser Engraving Workshop]] - darf natürlich angepasst werden!6 KB (767 words) - 16:38, 23 August 2021
- **laser cutting/engraving ([[Sebastian]])6 KB (987 words) - 15:32, 19 September 2022
- File:wood photo stand.png|simple but decorative holder for a [[Laser Engraving Photos|wooden photo]] out of leftovers from [[Project:TAC|my "TAC" boardgam9 KB (1,322 words) - 23:45, 18 May 2024