Herkules HMB 4000

Herkules HMB 4000

MachineInfoBox Herkules HMB 4000
Material:	metall
Used with:	1640 mm(?) Bandsaw Blades
Access Requirements:	Horizontal Bandsaw Introduction
Manual:	DE: assets.einhell.com
Tutors:	Lukas Johannes Sebastian

The exact name of this saw is not found anywhere on the case, but it's certainly a "Herkules HMB" series machine and we're going with model "4000" as the manual we could find comes extremely close at least. A generic name for this machine which is sold by different companies without apparent differences is "4x6 bandsaw".

This tool is not ready for use yet since not all commissioning steps have been completed. The process is also tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!

Task	comment	Status
Name the tool:	very similar newer model: Herkules HMB 4000	Herkules .....
Take a picture	-	done
Find the manual as PDF	probably similar enough: Herkules HMB 4000 (manualslib)	done
Documentation	this page, status: in commissioning	pending
Print QR-Code	use the wikicrawler	pending
Introduction	may need a separate intro from our vertical bandsaws - let's start by collecting everything here & see clear later	pending
Security Check	to be done or witnessed by a manager	pending
Test	known problem: needs new guide bearings (4x, type: ??)	pending
tool's name, owner and approx. value	donation from Mamad	pending
Last step: make it available	physically and in the wiki - then delete this template	pending

Specs

• motor: 245 W
• blade speeds: double-check & add label on machine, if not already there! 20-30-50 m/min according to manual
  • low: .........
  • medium: ..........
  • high: ...........
• blade length: 1640 mm (according to manual; double-check!)
• max. blade with: 13 mm (according to manual; double-check!)
• workpiece dimensions:
  • min. width: 6 mm with 10/14 TPI blade
  • max. width: 60 mm with 10/14 TPI blade
  • max. height: 100 mm (according to generic "4x6 inch" clearance; double-check!)
  • min. length: ???
  • max. length: potentially unlimited as long as you support all heavy sections with worktables

Changing Blades

We will usually only change the blade when it becomes dull to keep this saw well dialed-in. If you have special requirements, please reach out to a tutor!

New blades should be broken in before they can be run at the full feedrate.

A dull sawblade can be identified by eye (broken or chipped teeth, rough cut surfaces), ear (grinding noise), or feel (higher downward pressure required than usual). ^[1]

If you do need to change the blade, here's a nice video about adjusting a newly installed sawblade.

Upgrades

There is an interesting video series about improving this rather generic machine to a much higher standard.

Let's sum up the main ideas and our progress here:

• replace the standard blade with a bimetal one
  • according to the author, 14 tpi is already a bit too fine for many purposes as too many teeth are in the cut at once, but we'll need to see what kinds of tooth ratios are available

• replace certain screws with star knobs/knurled bolts for tool-free tightening?
• replace belt with a better fitting one? apparently, the originals are too thin
• check oil coverage in the gear box? (not shown, but apparently recommended by other online sources - as our machine is a bit old, we should keep this in mind)
• square the table and/or fences?
  • after some fiddling with the blade, we got pretty good results with aluminum in initial tests, but we should check the cast quality. Perhaps harder materials will show us we're still a bit off
• change spring bracket for lower balance position?
  • easy 180° flip would increase the distance by about 5 cm - would definitely be noticeable! We should do this if it turns out we never use the highest downward pressure (seems likely) or we need to go even lighter than the lowest possible setting
• add 90° stop (along with removing slack from the fixed fence screw: in the video, a bit of shrink tube already does the trick)
• add sliding tray to collect chips (in the video, he just used a simple plastic box lid)
• table for vertical use??
  • our saw has the required screw holes, but we should prohibit fiddling with this and keep the two machine types separate!