Herkules HMB 4000: Difference between revisions
From CoMakingSpace Wiki
(generic name; more rough upgrade notes from the intro video) |
(→Herkules HMB 4000: blades) |
||
| Line 11: | Line 11: | ||
|tutors=- | |tutors=- | ||
|manual=[https://assets.einhell.com/manuals-pdf/900_368289/hmb-4000.pdf ''DE: assets.einhell.com''] | |manual=[https://assets.einhell.com/manuals-pdf/900_368289/hmb-4000.pdf ''DE: assets.einhell.com''] | ||
|used with=1640 mm(?) [[Bandsaw Blades]] | |||
}} | }} | ||
The exact name of this saw is not found anywhere on the case, but it's certainly a "Herkules HMB" series machine and we're going with model "4000" as the manual we could find comes extremely close ''at least''. A generic name for this machine which is sold by different companies without apparent differences is "4x6 bandsaw". | The exact name of this saw is not found anywhere on the case, but it's certainly a "Herkules HMB" series machine and we're going with model "4000" as the manual we could find comes extremely close ''at least''. A generic name for this machine which is sold by different companies without apparent differences is "4x6 bandsaw". | ||
| Line 40: | Line 41: | ||
=== Specs === | === Specs === | ||
* motor: 245 W | * motor: 245 W | ||
* blade length: | * blade length: 1640 mm (according to manual; double-check!) | ||
* max. blade with: 13 mm (according to manual; double-check!) | |||
=== Upgrades === | === Upgrades === | ||
Revision as of 16:08, 9 January 2024
Herkules HMB 4000
| MachineInfoBox Herkules HMB 4000 | |
|---|---|
| |
| Material: | metall |
| Used with: | 1640 mm(?) Bandsaw Blades |
| Access Requirements: | Horizontal Bandsaw Introduction |
| Manual: | DE: assets.einhell.com |
| Tutors: | Lukas Johannes Sebastian |
The exact name of this saw is not found anywhere on the case, but it's certainly a "Herkules HMB" series machine and we're going with model "4000" as the manual we could find comes extremely close at least. A generic name for this machine which is sold by different companies without apparent differences is "4x6 bandsaw".
This tool is not ready for use yet since not all commissioning steps have been completed. The process is also tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!
| Task | comment | Status |
|---|---|---|
| Name the tool: | very similar newer model: Herkules HMB 4000 | Herkules ..... |
| Take a picture | - | done |
| Find the manual as PDF | probably similar enough: Herkules HMB 4000 (manualslib) | done |
| Documentation | this page, status: in commissioning | pending |
| Print QR-Code | use the wikicrawler | pending |
| Introduction | may need a separate intro from our vertical bandsaws - let's start by collecting everything here & see clear later | pending |
| Security Check | to be done or witnessed by a manager | pending |
| Test | known problem: needs new guide bearings (4x, type: ??) | pending |
| tool's name, owner and approx. value | donation from Mamad | pending |
| Last step: make it available | physically and in the wiki - then delete this template | pending |
Specs
- motor: 245 W
- blade length: 1640 mm (according to manual; double-check!)
- max. blade with: 13 mm (according to manual; double-check!)
Upgrades
There is an interesting video series about improving this rather generic machine to a much higher standard.
Let's sum up the main ideas and our progress here:
- replace the standard blade with a bimetal one
- according to the author, 14 tpi is already a bit too fine for many purposes as too many teeth are in the cut at once, but we'll need to see what kinds of tooth ratios are available
- replace certain screws with star knobs/knurled bolts for tool-free tightening?
- replace belt with a better fitting one? apparently, the originals are too thin
- check oil coverage in the gear box? (not shown, but apparently recommended by other online sources - as our machine is a bit old, we should keep this in mind)
- square the table and/or fences?
- after some fiddling with the blade, we got pretty good results with aluminum in initial tests, but we should check the cast quality. Perhaps harder materials will show us we're still a bit off
- change spring bracket for lower balance position?
- add 90° stop (along with removing play from the fixed fence screw
- add sliding tray to collect chips (in the video, he just used a simple plastic box lid)
- table for vertical use??
- if included with our saw, we should probably remove this and keep the two machine types separate!
