Chop Saw Introduction: Difference between revisions
(→Safety: 10 million dollar stick) |
No edit summary |
||
(8 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
This is the content required for an introduction to our [[Chop Saw|chop saw]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | This is the content required for an introduction to our [[Introduction for::Chop Saw|chop saw]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | ||
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Lukas|Lukas]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Keno|Keno]], [[Tutor::User:Sebastian|Sebastian]], [[Tutor::User:Utis|Utis]], [[Tutor::User:Loewenstein|Jan]], [[Tutor::User:Jakob|Jakob]] | |||
Let's begin! First off, make sure you have read the machine's [https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290462v21_160992A4CT_201808.pdf manual]. | Let's begin! First off, make sure you have read the machine's [https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290462v21_160992A4CT_201808.pdf manual]. | ||
Line 17: | Line 19: | ||
|- | |- | ||
| sawdust and small splinters can fly towards the operator and others || | | sawdust and small splinters can fly towards the operator and others || | ||
* hook up a [[Shop Vac|shop vac]], but be aware the dust extraction from | * hook up a [[Shop Vac|shop vac]], but be aware the dust extraction will still be incomplete | ||
** the large saw draws too much power to be connected through the shop vac's on-board outlet, but should be powered from a separate power outlet instead | |||
* wear [[goggles]] | * wear [[goggles]] | ||
* [[Dust Mask|dust mask]]: depending on the material you're cutting | * [[Dust Mask|dust mask]]: depending on the material you're cutting | ||
Line 40: | Line 43: | ||
{{Waiting List}} | {{Waiting List}} | ||
{{#set: | |||
| checklist_title=Chop Saw | |||
| checklist_symbols=M004 | |||
| checklist_symbols=M003 | |||
| checklist_symbols=M002 | |||
| checklist_symbols=M016 | |||
| checklist_link=https://wiki.comakingspace.de/index.php?title=Chop_Saw_Introduction | |||
| checklist_before=**Must** check if cut interferes in any way (e.g. fence) | |||
| checklist_before=**Must not** use shop vac outlet (too much startup current) | |||
| checklist_before=**Must not** fix workpiece on both sides at once | |||
| checklist_before=**Should** fix articulating arm if not needed | |||
| checklist_during=**Must** cut from front to back when using articulating arm | |||
| checklist_after=cleanup | |||
}} | |||
[[Category:Introductions]] | [[Category:Introductions]] |
Latest revision as of 21:12, 21 February 2024
This is the content required for an introduction to our chop saw - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
If you need this introduction, please reach out to the following tutors: Patrick, Lukas, Luzian, Martin, Johannes, Keno, Sebastian, Utis, Jan, Jakob
Let's begin! First off, make sure you have read the machine's manual.
Safety
(a dust mask could also be necessary depending on your material)
Dangers | Precautions |
---|---|
sharp and rotating exposed blade - will keep spinning for a bit after turning the power off! |
|
sawdust and small splinters can fly towards the operator and others | |
kickback: workpiece can move during the cut or cause the blade to push itself up |
|
cutting the incorrect material for a saw blade type |
|
Demonstration
The tutor will show you these steps in detail:
- adjusting the bevel
- adjusting the rotation
- setting the depth stop
- releasing the blade guard and starting the saw
Waiting List
This introduction takes longer than many others and usually can't be done spontaneously during regular opening times. If you would like to receive it, please add yourself to >> this list << and we will find a good time once a few members are on it!