Inclinometer: Difference between revisions
(use instead of winding sticks) |
m (location) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{ToolInfoBox | {{ToolInfoBox | ||
|tool name=Inclinometer | |tool name=Inclinometer | ||
|image=inclinometer.JPG | |german=Neigungsmesser|image=inclinometer.JPG | ||
|synonyms=level box, bevel box, digital angle cube;<br>DE: Neigungsmesser, Neigungssensor,<br>digitale Wasserwaage | |synonyms=level box, bevel box, digital angle cube;<br>DE: Neigungsmesser, Neigungssensor,<br>Winkelbox, digitale Wasserwaage | ||
|type=[[measuring]] tool | |type=[[measuring]] tool | ||
|material= | |material= | ||
|used with=[[Table Saw|table saw]], [[Chop Saw|chop saw]],<br>[[Drill Press|drill press]] (bit more difficult) | |used with=[[Table Saw|table saw]], [[Chop Saw|chop saw]],<br>[[Drill Press|drill press]] (bit more difficult) | ||
|location=[[Location:: | |location=cart near [[Location::Measuring Shelf|measuring shelf]] | ||
|access=read this page & the manual | |access=read this page & the manual | ||
|manual=in the box | |manual=in the box | ||
|similar=[[squares]], [[levels]], [[goniometer]] | |similar=[[squares]], [[levels]], [[goniometer]] | ||
}} | }} | ||
| Line 18: | Line 16: | ||
== [[Table Saw]] or [[Chop Saw]] == | == [[Table Saw]] or [[Chop Saw]] == | ||
To use, simply reference the saw's table as "zero", then let the tool snap to the side of the blade and adjust the vertical bevel until you're happy. | '''Blade angle:''' To use, simply reference the saw's table as "zero", then let the tool snap to the side of the blade and adjust the vertical bevel until you're happy. | ||
'''Table saw miter fence:''' we could build [https://www.instagram.com/p/B4icOVZneAP a jig that holds the miter fence upright for setting its inclination]! | |||
== [[Drill Press]] == | == [[Drill Press]] == | ||
Latest revision as of 20:30, 20 May 2024
| ToolInfoBox Inclinometer | |
|---|---|
| |
| Synonyms: | level box, bevel box, digital angle cube; DE: Neigungsmesser, Neigungssensor, Winkelbox, digitale Wasserwaage |
| Type: | measuring tool |
| Used with: | table saw, chop saw, drill press (bit more difficult) |
| Location: | cart near measuring shelf |
| Access Requirements: | read this page & the manual |
| Manual: | in the box |
| Similar (More or Less): | squares, levels, goniometer |
A digital inclinometer with a magnetic base is an awesome helper for adjusting circular saw blades to a precise angle! Lukas is sharing this one on the marking & measuring shelf in the wood workshop.
Before you put the inclinometer back into its box, make sure to turn it off by holding the ON/OFF/REF button for a few seconds.
Table Saw or Chop Saw
Blade angle: To use, simply reference the saw's table as "zero", then let the tool snap to the side of the blade and adjust the vertical bevel until you're happy.
Table saw miter fence: we could build a jig that holds the miter fence upright for setting its inclination!
Drill Press
It's a bit trickier to get a good reference on the drill press as you'll have to reference the vertical chuck (or drill bit) and the horizontal table is the moving part - but it pays out when you want to drill precisely!
Other Uses
- an inclinometer placed on top of a straightedge (like a sideways metal plane) can supposedly replace a pair of winding sticks - the straightedge is slid over the workpiece and you gradually remove material until you get a constant inclination reading [1]
