Plastic Shredder Introduction: Difference between revisions
From CoMakingSpace Wiki
NitramLegov (talk | contribs) m (Blades will keep spinning a while after turning it of) |
(→Safety: stalled motor = bad (I believe Johannes told me about this)) |
||
(5 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
This is the content required for an introduction to our [[Introduction for::Plastic Shredder]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | This is the content required for an introduction to our [[Introduction for::Plastic Shredder]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | ||
If you need this introduction, please reach out to the following tutors: | If you need this introduction, please reach out to the following tutors: [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Lukas|Lukas]] | ||
Let's begin! First off, make sure you have read the machine's entire [[Plastic Shredder|wiki page]]. | Let's begin! First off, make sure you have read the machine's entire [[Plastic Shredder|wiki page]]. | ||
Line 16: | Line 13: | ||
!Dangers!! Precautions | !Dangers!! Precautions | ||
|- | |- | ||
|[[File:danger - sharp objects.svg|50px]] [[File:danger - draw-in.svg|50px]]<br>rotating blades - will keep spinning for a bit after turning the power off!| | |[[File:danger - sharp objects.svg|50px]] [[File:danger - draw-in.svg|50px]]<br>rotating blades - will keep spinning for a bit after turning the power off! | ||
| | |||
* The blade motor will automatically stop when the hopper is not closed. You MUST test this feature each time before you start working! | |||
You MUST wear [[Goggles|eye protection]] when operating the machine | * You MUST wear [[Goggles|eye protection]] when operating the machine | ||
You MUST NOT wear [[gloves]] | * You MUST NOT wear [[gloves]] | ||
You MUST NOT stick any body parts into the hopper | * You MUST NOT stick any body parts into the hopper | ||
You MUST keep your hands well clear of the blades until they stopped completely | * You MUST keep your hands well clear of the blades until they stopped completely | ||
|- | |- | ||
|flying bits of plastic||You MUST wear [[Goggles|eye protection]] in case something gets out past the cover. | |flying bits of plastic||You MUST wear [[Goggles|eye protection]] in case something gets out past the cover. | ||
|- | |||
|large, hard pieces can jam the blades - the stalled motor will throw a fuse after a couple of seconds | |||
| | |||
* You MUST turn off the machine as soon as there is a jam | |||
* You SHOULD try to prepare your plastic in manageable portions | |||
|} | |} | ||
==Demonstration== | ==Demonstration== | ||
Line 35: | Line 37: | ||
'''Preparation''' | '''Preparation''' | ||
* Check the collection box is clean, otherwise remove any dust and small bits with a damp cloth | |||
* | |||
* Check the shredder is clean | * Check the shredder is clean | ||
* Put the box under the shredder | * Put the box under the shredder | ||
'''Shredding''' | '''Shredding''' | ||
* Close the hopper | * Close the hopper | ||
* Start the shredder motor | * Start the shredder motor | ||
* | * If needed, gently push material down the hopper (with a stick, not your hand!) | ||
'''Cleanup''' | '''Cleanup''' | ||
* Turn off the motor | * Turn off the motor | ||
* If you shredded more than you need, please share with the others! Make sure to select the right storage box for your material (plastic type and approximate color) | |||
* Clean the hopper | * Clean the hopper | ||
* Clean the shredder blades | * Clean the shredder blades | ||
* Clean the collection box, making sure to get all the small bits out (a damp cloth should help) | |||
[[Category:Introductions]] | [[Category:Introductions]] |
Latest revision as of 16:06, 8 April 2023
This is the content required for an introduction to our Plastic Shredder - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
If you need this introduction, please reach out to the following tutors: Martin, Lukas
Let's begin! First off, make sure you have read the machine's entire wiki page.
Safety
Dangers | Precautions |
---|---|
rotating blades - will keep spinning for a bit after turning the power off! |
|
flying bits of plastic | You MUST wear eye protection in case something gets out past the cover. |
large, hard pieces can jam the blades - the stalled motor will throw a fuse after a couple of seconds |
|
Demonstration
The tutor will show you these steps in detail:
Preparation
- Check the collection box is clean, otherwise remove any dust and small bits with a damp cloth
- Check the shredder is clean
- Put the box under the shredder
Shredding
- Close the hopper
- Start the shredder motor
- If needed, gently push material down the hopper (with a stick, not your hand!)
Cleanup
- Turn off the motor
- If you shredded more than you need, please share with the others! Make sure to select the right storage box for your material (plastic type and approximate color)
- Clean the hopper
- Clean the shredder blades
- Clean the collection box, making sure to get all the small bits out (a damp cloth should help)