Router Table Introduction: Difference between revisions
From CoMakingSpace Wiki
(this was included in "Handheld Router Introduction" until 2020-4-15) |
m (add tutor Luzian) |
||
| (8 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
This is the content required for an introduction to our [[Introduction for::Router Table|router table]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | |||
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Lukas|Lukas]], [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Keno|Keno]], [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Utis|Utis]], [[Tutor::User:Luzian|Luzian]] | |||
'''The [[Handheld Router Introduction|handheld router introduction]] is required as a background for this introduction!''' | '''The [[Handheld Router Introduction|handheld router introduction]] is required as a background for this introduction!''' | ||
''If you received that introduction before 2020-4-15, it still included the router table part and you only need to make sure you now '''watch both pages for updates.''' And as always: feel free to ask for a refresher whenever anything is not clear anymore!'' | ''If you received that introduction before 2020-4-15, it still included the router table part and you only need to make sure you now '''watch both pages for updates.''' And as always: feel free to ask for a refresher whenever anything is not clear anymore!'' | ||
[[File:Router table feed direction animation.GIF|thumb|right|300 px|proper feed directions for safe '''push cuts''' - click to see an animation!]] | |||
[[File:router table - starting pin.png|thumb|right|300px|a starting pin helps you make sure your workpiece stays in front of the router bit if you can't use a fence!]] | |||
When working on a [[Router Table|router table]], '''additional''' care needs to be taken as the router is turned upside down in a fixed position! | When working on a [[Router Table|router table]], '''additional''' care needs to be taken as the router is turned upside down in a fixed position! | ||
* the workpiece can be grabbed and shot across the room if you attempt a climb cut, '''only do push cuts'''! | * the workpiece can be grabbed and shot across the room if you attempt a climb cut, '''only do push cuts'''! | ||
** '''only feed from right to left when you work in front of the bit!''' | ** '''only feed from right to left when you work in front of the bit!''' | ||
** see schematic for other cases, but make sure you really '''understand''' what's going on | ** see schematic for other cases, but make sure you really '''understand''' what's going on | ||
* keep all body parts at least a hand's width away from the exposed bit (use [[Push Blocks|push blocks]] if that's not possible) | * keep all body parts at least a hand's width away from the exposed bit (use [[Push Blocks|push blocks]] if that's not possible) | ||
* use all possible fences, guards, [[featherboards]] etc. to secure the workpiece and reduce exposure of the bit | * use all possible fences, guards, [[featherboards]] etc. to secure the workpiece and reduce exposure of the bit | ||
* make use of a starting pin (or similar) when working fenceless with a bearing bit<sup> [https://www.popularwoodworking.com/tools/10-router-tips-for-furniture-makers/ tip #6]</sup> | * make use of a starting pin (or similar) when working fenceless with a bearing bit<sup> [https://www.popularwoodworking.com/tools/10-router-tips-for-furniture-makers/ tip #6]</sup> | ||
==Demonstration== | |||
The tutor will show you in detail how to: | |||
* Adjust and lock the height of the router | |||
* Insert the bit into the router | |||
* Tighten the collet (best through the top of the table) | |||
* Turn the router on and off by using the safety switch of the router table | |||
* How to properly store the fence '''together with all small parts''' so stuff does not get lost all the time! | |||
[[Category:Introductions]] | [[Category:Introductions]] | ||
Latest revision as of 01:01, 15 August 2024
This is the content required for an introduction to our router table - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
If you need this introduction, please reach out to the following tutors: Lukas, Martin, Keno, Patrick, Utis, Luzian
The handheld router introduction is required as a background for this introduction!
If you received that introduction before 2020-4-15, it still included the router table part and you only need to make sure you now watch both pages for updates. And as always: feel free to ask for a refresher whenever anything is not clear anymore!
When working on a router table, additional care needs to be taken as the router is turned upside down in a fixed position!
- the workpiece can be grabbed and shot across the room if you attempt a climb cut, only do push cuts!
- only feed from right to left when you work in front of the bit!
- see schematic for other cases, but make sure you really understand what's going on
- keep all body parts at least a hand's width away from the exposed bit (use push blocks if that's not possible)
- use all possible fences, guards, featherboards etc. to secure the workpiece and reduce exposure of the bit
- make use of a starting pin (or similar) when working fenceless with a bearing bit tip #6
Demonstration
The tutor will show you in detail how to:
- Adjust and lock the height of the router
- Insert the bit into the router
- Tighten the collet (best through the top of the table)
- Turn the router on and off by using the safety switch of the router table
- How to properly store the fence together with all small parts so stuff does not get lost all the time!
