Reciprocating Saw Introduction: Difference between revisions

Latest revision as of 20:37, 19 June 2024

This is the content required for an introduction to our reciprocating saw and jigsaws - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)

If you need this introduction, please reach out to the following tutors: Lukas, Patrick, Johannes, Luzian, Sebastian, Utis

Let's begin! First off, make sure you have read the corresponding tool's manual:

Safety

Personal protection:

Additional protection for toxic or allergenic woods (especially hardwoods, e.g. beech and oak - see "dust") or for certain surface finishes or chemicals:

Dangers	Precautions
sharp oscillating blade - possible kickback	you MUST NOT turn on the saw when the blade is already touching something (e.g. the workpiece) you MUST let the baseplate touch the workpiece before starting to cut blind cut: leave the sawblade in the cut until it has stopped through cut: make sure the blade has stopped moving before putting the saw back on the table you MUST make sure the blade path is free and you won't cut into the table or similar you MUST make sure the blade is long enough so that it can reach through the material when fully retracted (too short a blade relative to the material being cut will cause dangerous kickback) you MUST make sure there are no obstacles such as nails in your path before starting a cut you MUST secure the workpiece with clamps so nothing shifts and nothing large falls down once the cut is made
generates dust and small chips	you MUST wear goggles you SHOULD hook up the shop vac (and deactivate the "dust blow" function of the saw, if available) if your workpiece is contaminated with chemicals or made from hard woods like beech (Buche) or oak (Eiche), you SHOULD use a dust mask
generates noise	you MUST wear ear defenders
the blade can get very hot remains hot for a while after using	when you see smoke, immediately stop and inspect the saw - the blade might be dull or jammed in the workpiece. Also do not stay in the same place for too long!
no prevention of turning on after loss & restoration of power (keine Anlaufsicherung)	you MUST make sure the locking button is "off" before plugging the saw in (the trigger should move freely)

Demonstration

During the introduction, the tutor will show you the following:

inserting/removing saw blades
choosing and changing the pendulum or orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)

Besides these safety notes, you should know which type of blade is suitable for the material you want to cut!

@@ Line 1: / Line 1: @@
-{{incomplete}}
+This is the content required for an introduction to our [[Introduction for::Reciprocating Saw| reciprocating saw]] and [[Introduction for::jigsaws]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
-This is the content required for an introduction to our [[Reciprocating Saw| reciprocating saw]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
+If you need this introduction, please reach out to the following tutors: [[Tutor::User:Lukas|Lukas]], [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:Sebastian|Sebastian]], [[Tutor::User:Utis|Utis]]
-Let's begin! First off, make sure you have read the tool's manual (Bosch PFZ 700 PE: [https://www.manualslib.com/manual/1125358/Bosch-Pfz-700-Pe.html here]).
+Let's begin! First off, make sure you have read the corresponding tool's manual:
+* [https://www.manualslib.com/manual/1125358/Bosch-Pfz-700-Pe.html Bosch PFZ 700 PE]
+* [http://www.lidl-service.com/static/134937369/114249_DE.pdf Parkside PSTD 800 A1]
+* [https://www.manualslib.com/manual/1115989/Bosch-Pst-650-Pe.html Bosch PST 750 PE]
 == Safety ==
-=== Dangers ===
+[[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]][[File:Protection - hearing.svg|50x50px]]
-* sharp oscillating blade - possible kickback
-* generates dust and small chips
-* generates noise
-=== Precautions ===
+''Additional protection for toxic or allergenic woods (especially hardwoods, e.g. beech and oak - see "[[dust]]") or for certain surface finishes or chemicals:'' [[File:Protection - breathing.svg|50x50px]]
-* make sure the blade path is free and you won't cut into the table or similar
-* make sure the blade is long enough so that it can reach through the material when fully retracted. (too short a blade relative to the material being cut will cause dangerous kickback)
+{| class="wikitable"
-* before cutting into the workpiece, make sure there are no obstacles such as nails in it
+|-
-* secure the workpiece with [[clamps]] so nothing shifts and nothing large falls down once the cut is made
+! Dangers !! Precautions
-* wear [[goggles]]
+|-
-** perhaps also wear a [[Dust Masks|dust mask]] (depending on the material you're cutting)
+| sharp oscillating blade - possible kickback ||
-* wear [[Ear Defenders|ear defenders]]
+* you MUST NOT turn on the saw when the blade is already touching something (e.g. the workpiece)
-* make sure the locking lever isn't "on" before plugging the saw in (the trigger should move freely)
+* you MUST let the baseplate touch the workpiece before starting to cut
-* make sure the blade is not moving before putting the saw back on the table
+* blind cut: leave the sawblade in the cut until it has stopped
-* in order to avoid kickback: never turn on the saw when the blade is touching something (e.g. the workpiece)
+* through cut: make sure the blade has stopped moving before putting the saw back on the table
-* always let the baseplate touch the workpiece before starting to cut
+* you MUST make sure the blade path is free and you won't cut into the table or similar
-* leave the sawblade in the cut until it has stopped
+* you MUST make sure the blade is long enough so that it can reach through the material when fully retracted (too short a blade relative to the material being cut will cause dangerous kickback)
+* you MUST make sure there are no obstacles such as nails in your path before starting a cut
+* you MUST secure the workpiece with [[clamps]] so nothing shifts and nothing large falls down once the cut is made
+|-
+| generates dust and small chips ||
+* you MUST wear [[goggles]]
+* you SHOULD hook up the [[Shop Vac|shop vac]] (and deactivate the "dust blow" function of the saw, if available)
+* if your workpiece is contaminated with chemicals or made from hard woods like beech ''(Buche)'' or oak ''(Eiche)'', you SHOULD use a [[Dust Mask|dust mask]]
+|-
+| generates noise ||
+* you MUST wear [[Ear Defenders|ear defenders]]
+|-
+|
+the blade can get very hot
+* remains hot for a while after using
+|| when you see smoke, immediately stop and inspect the saw - the blade might be dull or jammed in the workpiece. Also do not stay in the same place for too long!
+|-
+| [[File:Danger_-_sudden_start.svg|left|50px]] no prevention of turning on after loss & restoration of power (''keine Anlaufsicherung'') ||
+* you MUST make sure the locking button is "off" before plugging the saw in (the trigger should move freely)
+|}
 == Demonstration ==
 During the introduction, the tutor will show you the following:
 * inserting/removing saw blades
-* choosing and changing the orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)
+* choosing and changing the pendulum or orbital action settings (Bosch PFZ 700 PE: chapter 7 in the manual)
 Besides these safety notes, you should know which type of blade is suitable for the material you want to cut!