Project:Tree Trunk Tealights: Difference between revisions
(→Making: more gallery) |
m (Category:Lighting) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{ProjectInfoBox | {{ProjectInfoBox | ||
|project title=Tealight Holders out of Birch Logs | |project title=Tealight Holders out of Birch Logs | ||
|image= | |image=birch tealights 10.JPG | ||
|status=about 40 made, now documenting | |status=about 40 made, now documenting | ||
|date=spring 2018 | |date=spring 2018 | ||
| Line 10: | Line 10: | ||
|cost= | |cost= | ||
}} | }} | ||
''documentation unfinished, | ''documentation unfinished, please just ask if you have urgent questions ;-) '' | ||
I made a bunch of tealight holders out of birch trunks as a wedding decoration and will now work on turning this project into a woodworking [[seminar]] for beginners. | I made a bunch of tealight holders out of birch trunks as a wedding decoration and will now work on turning this project into a woodworking [[seminar]] for beginners. | ||
| Line 30: | Line 30: | ||
* sand cut faces with [[Eccentric Sander|eccentric sander]] | * sand cut faces with [[Eccentric Sander|eccentric sander]] | ||
* let dry - continue & seal ends immediately next time? | * let dry - continue & seal ends immediately next time? | ||
* drill with | * drill with 1-5/8" [[Forstner Bit|Forstner bit]] | ||
* let dry/seal again so the bottom of the hole is protected | * let dry/seal again so the bottom of the hole is protected | ||
* insert steel holder before the log shrinks too much! | * insert steel holder before the log shrinks too much! | ||
| Line 41: | Line 41: | ||
File:birch tealights 05.JPG|we then [[Sanding|sanded]] off the mold and force-dried the cut faces with a [[Heat Gun|heat gun]] | File:birch tealights 05.JPG|we then [[Sanding|sanded]] off the mold and force-dried the cut faces with a [[Heat Gun|heat gun]] | ||
File:birch tealights 06.JPG|after superficial heating, we applied [[Hard Wax Oil|hard wax oil]] in an attempt to protect the wood | File:birch tealights 06.JPG|after superficial heating, we applied [[Hard Wax Oil|hard wax oil]] in an attempt to protect the wood | ||
File:birch tealights 07.JPG|another week of drying on my | File:birch tealights 07.JPG|another week of drying on my workbench with better spacing | ||
File:birch tealights 08.JPG|there was still some new mold after all this, but it was easily sanded off by hand | File:birch tealights 08.JPG|there was still some new mold after all this, but it was easily sanded off by hand | ||
File:birch tealights 09.JPG|finally, the logs were ready for drilling with a large [[Forstner Bit|Forstner bit]] | File:birch tealights 09.JPG|finally, the logs were ready for drilling with a large [[Forstner Bit|Forstner bit]] | ||
| Line 49: | Line 49: | ||
</gallery> | </gallery> | ||
[[Category:Lighting]] | |||
[[Category:Quick Projects]] | [[Category:Quick Projects]] | ||
[[Category:Woodworking]] | [[Category:Woodworking]] | ||
[[Category:Wedding]] | |||
Latest revision as of 18:43, 3 September 2023
| ProjectInfoBox Tealight Holders out of Birch Logs | |
|---|---|
| |
| Status: | about 40 made, now documenting |
| Release Date: | spring 2018 |
| Initiator: | Lukas |
| Team: | Gesa |
| Materials Used: | birch logs, coconut oil, steel tealight cups, tealights |
| Tools Used: | chop saw (and crosscut saw where too thick), drill press & Forstner bit, eccentric sander, sandpaper |
documentation unfinished, please just ask if you have urgent questions ;-)
I made a bunch of tealight holders out of birch trunks as a wedding decoration and will now work on turning this project into a woodworking seminar for beginners.
Materials
Birch Logs
- from Bauhaus, very wet!
- better cut & dry in advance next time??
- risk of mold forming at the cut faces...
Tealights
- steel holders from <smile link>
- "eco" tealights without aluminum cases <smile link>
Making
Need to test whether this can be sped up - drilling into the wet wood was very difficult! Lots of unforeseen mold problems..
- cut with chop saw - log often too thick for the small Herkules saw...switch to bandsaw next time?
- sand cut faces with eccentric sander
- let dry - continue & seal ends immediately next time?
- drill with 1-5/8" Forstner bit
- let dry/seal again so the bottom of the hole is protected
- insert steel holder before the log shrinks too much!
- gallery
the store-bought logs were very wet and quickly became moldy...
cutting approx. 8-10 cm long pieces with the chop saw
the logs were often too thick for our (then) available power saws and needed to be finished off by hand with a crosscut saw
a lot of mold formed again within a week after cutting...
after superficial heating, we applied hard wax oil in an attempt to protect the wood
another week of drying on my workbench with better spacing
there was still some new mold after all this, but it was easily sanded off by hand
finally, the logs were ready for drilling with a large Forstner bit
more drilling...good to have a drill press available!
after shaping, the ends were finished with coconut oil
make sure to insert the steel cups soon afterwards, the wood (and the hole!) will shrink as it keeps drying
