Tyme Avon: Difference between revisions
From CoMakingSpace Wiki
NitramLegov (talk | contribs) m (br clear statement) |
(→Specs: measured up) |
||
| Line 42: | Line 42: | ||
=== Specs === | === Specs === | ||
We seem to have the Model ATL301 with 36" (915 mm) between centers and a bed length of 52" (1320 mm). | |||
* max. workpiece diameter (above bed): 280 mm (11") | * max. workpiece diameter (above bed): 280 mm (11") | ||
** max. workpiece diameter (swiveled 90°): 495 mm (19.5") | ** max. workpiece diameter (swiveled 90°): 495 mm (19.5") | ||
** max. workpiece diameter (swiveled 180°): 610 mm (24") | ** max. workpiece diameter (swiveled 180°): 610 mm (24") | ||
* max. workpiece length: | * max. workpiece length: 900 mm | ||
* spindle speeds: 470 - 750 - 1150 - 2000 rpm | * spindle speeds: 470 - 750 - 1150 - 2000 rpm | ||
* motor: 550 W (3/4 hp) | * motor: 550 W (3/4 hp) | ||
* spindle thread: | * spindle thread: M25{{x}}2 mm; internal No. 2 morse taper (MK2) | ||
* workholding options: | * workholding options: | ||
** headstock: | ** headstock: drive center, [[faceplate]], [[Four-Jaw Chucks|four-jaw chuck]], ... | ||
** tailstock: | ** tailstock: No. 2 morse taper (MK2) - accessories: rotating center, our "usual" drill chucks also fit | ||
<br clear="all" /> | <br clear="all" /> | ||
Revision as of 20:33, 23 September 2022
Tyme Avon
| MachineInfoBox Tyme Avon | |
|---|---|
| |
| Material: | woodturning blanks |
| Used with: | face shield, woodturning tools |
| Access Requirements: | Woodturning Introduction |
| Tutors: | Lukas |
The Tyme Avon is an old, but solidly built lathe that will soon replace the flimsy Güde 1000.
This tool is not ready for use yet since not all commissioning steps have been completed. The process is not yet tracked on GitHub. Feel free to contribute to making it usable, any help is very welcome!
| Task | comment | Status |
|---|---|---|
| Name the tool: | Tyme Avon (exact model TBD by bed length) | pending |
| Take a picture | - | pending |
| Find the manual as PDF | print version for sale (expensive) here; reportedly not very useful beyond machine specs | not available |
| Documentation | explain (& photograph?) all major accessories and setup options; possible starting point besides manual: http://www.lathes.co.uk/tyme/ | pending |
| Print QR-Code | use the wikicrawler | pending |
| Introduction | Woodturning Introduction may need slight changes - TBD | pending |
| Security Check | was fitted with an EU plug and a longer cord by Johannes; belt runs into the side of its pulleys -> move one pulley by approx. 1 mm | pending |
| Test | to be done or witnessed by a manager | pending |
| tool's name, owner and approx. value | donated by Joe; value not yet known | pending |
| Last step: make it available | physically and in the wiki - then delete this template | pending |
Specs
We seem to have the Model ATL301 with 36" (915 mm) between centers and a bed length of 52" (1320 mm).
- max. workpiece diameter (above bed): 280 mm (11")
- max. workpiece diameter (swiveled 90°): 495 mm (19.5")
- max. workpiece diameter (swiveled 180°): 610 mm (24")
- max. workpiece length: 900 mm
- spindle speeds: 470 - 750 - 1150 - 2000 rpm
- motor: 550 W (3/4 hp)
- spindle thread: M25 × 2 mm; internal No. 2 morse taper (MK2)
- workholding options:
- headstock: drive center, faceplate, four-jaw chuck, ...
- tailstock: No. 2 morse taper (MK2) - accessories: rotating center, our "usual" drill chucks also fit
