Handheld Sander Introduction: Difference between revisions
From CoMakingSpace Wiki
(→Safety: turned into table (as discussed in #136)) |
(→Safety: goggles: not always required!) |
||
| (7 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
This is the content required for an introduction to our handheld [[sanders]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | This is the content required for an introduction to our handheld [[sanders]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-) | ||
Let's begin! First off, make sure you have read the machine's manual (should be linked from its wiki page). | This introduction is valid for the following machines: | ||
* [[Introduction for::Belt Sander]] | |||
* [[Introduction for::Eccentric Sanders]] | |||
* [[Introduction for::Sheet Sanders]] | |||
* [[Introduction for::Delta Sander]] | |||
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Lukas|Lukas]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Keno|Keno]], [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:Sebastian|Sebastian]], [[Tutor::User:Jakob|Jakob]], [[Tutor::User:Lmnl99|Luca]]. | |||
Let's begin! First off, make sure you have read the machine's wiki page and manual (should be linked from its wiki page). | |||
== Safety == | == Safety == | ||
[[PPE|Personal protection]]: [[File:Protection - breathing.svg|50px]] [[File:Protection - goggles.svg|50px]] | [[PPE|Personal protection]]: [[File:Protection - breathing.svg|50px]] | ||
+ when working with metal or small workpieces: [[File:Protection - goggles.svg|50px]] | |||
''[[ear defenders]] and [[gloves]] are also recommended when working with a sander (and [[Shop Vac|shop vac]]) for an extended amount of time'' | ''[[ear defenders]] and [[gloves]] are also recommended when working with a sander (and [[Shop Vac|shop vac]]) for an extended amount of time'' | ||
| Line 13: | Line 23: | ||
|- | |- | ||
| '''lots''' of fine dust from wood or plastics - can irritate lungs and skin || | | '''lots''' of fine dust from wood or plastics - can irritate lungs and skin || | ||
* wear a [[Dust Mask|dust mask]] and long clothes if your material generates hazardous dust | * wear a [[Dust Mask|dust mask]] and long clothes if your material generates hazardous [[dust]] | ||
* check for a clean run and fit of the sanding medium before you start; check if hole alignment for the dust extraction is correct | * check for a clean run and fit of the sanding medium before you start; check if hole alignment for the dust extraction is correct | ||
* sand '''outside''' if you can't connect a [[Shop Vac|shop vac]] or fine filter | * sand '''outside''' if you can't connect a [[Shop Vac|shop vac]] or fine filter | ||
| Line 26: | Line 36: | ||
* secure your workpiece and exert a firm grip on the tool | * secure your workpiece and exert a firm grip on the tool | ||
* let the tool get to full speed before contacting your workpiece and start with light pressure | * let the tool get to full speed before contacting your workpiece and start with light pressure | ||
** '''exception''': [[Eccentric Sanders|eccentric sanders]] only work correctly when under load and may leave marks if you lift and lower them while running - they are best started '''on''' the workpiece<sup> [https://www.schleifprofi.com/schleifmaschinen/exzenterschleifer/] & [[HolzWerken]] 115</sup> | |||
|- | |- | ||
| [[File:Danger_-_sudden_start.svg|left|50px]] some of the sanders have no prevention of turning on after loss & restoration of power ''(keine Anlaufsicherung)'' || make sure the tool is turned off before plugging it in | | [[File:Danger_-_sudden_start.svg|left|50px]] some of the sanders have no prevention of turning on after loss & restoration of power ''(keine Anlaufsicherung)'' || make sure the tool is turned off before plugging it in | ||
Latest revision as of 09:14, 14 September 2024
This is the content required for an introduction to our handheld sanders - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)
This introduction is valid for the following machines:
If you need this introduction, please reach out to the following tutors: Lukas, Johannes, Keno, Martin, Patrick, Luzian, Sebastian, Jakob, Luca.
Let's begin! First off, make sure you have read the machine's wiki page and manual (should be linked from its wiki page).
Safety
+ when working with metal or small workpieces: 
ear defenders and gloves are also recommended when working with a sander (and shop vac) for an extended amount of time
| Dangers | Precautions |
|---|---|
| lots of fine dust from wood or plastics - can irritate lungs and skin |
|
| sparks from sanding metal |
|
| powerful movements can make the workpiece shift (or fly!) and let a handheld sander "run away" |
|
 |
make sure the tool is turned off before plugging it in |
Protect the Velcro
Do NOT sand with parts of the velcro pad uncovered - this will wear it out and lead to much poorer bonding of the next piece of sandpaper!
Suggested Reading
Besides these safety notes, you should read the page about dust to get a better conception of the dangers associated with some materials! Remember, you are responsible for the material you choose and for protecting yourself.
