Handheld Circular Saw Introduction: Difference between revisions

From CoMakingSpace Wiki

(→‎Safety: turned dangers/precautions into table as suggested in #136)
(removed Herkules saw (RIP); riving knife does NOT need to be removed)
 
(9 intermediate revisions by 4 users not shown)
Line 1: Line 1:
This is the content required for an introduction to our [[Circular Saws|circular saws]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
This is the content required for an introduction to our [[Introduction for::Handheld Circular Saws|handheld circular saws]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
 
If you need this introduction, please reach out to the following tutors: [[Tutor::User:Pakue|Patrick]], [[Tutor::User:Lukas|Lukas]], [[Tutor::User:NitramLegov|Martin]], [[Tutor::User:Keno|Keno]], [[Tutor::User:Johannes|Johannes]], [[Tutor::User:Luzian|Luzian]], [[Tutor::User:Utis|Utis]]


Let's begin! First off, make sure you have read the machine's manual:
Let's begin! First off, make sure you have read the machine's manual:
* [https://www.manualslib.com/manual/1230277/Einhell-E-Hks.html#manual Herkules BHK 1600LE "Laser Beam"]
* [https://www.manualslib.com/manual/1311650/Festool-Ts-75-Ebq.html Festool TS 75 EBQ] (plunge saw)
* [https://www.manualslib.com/manual/1311650/Festool-Ts-75-Ebq.html Festool TS 75 EBQ] (plunge saw)


Line 24: Line 25:
** attach the endstop to the rail to reduce the chance of kickback  
** attach the endstop to the rail to reduce the chance of kickback  
** use an appropriately sized riving knife ''(DE: Spaltkeil)'' for the blade you're using
** use an appropriately sized riving knife ''(DE: Spaltkeil)'' for the blade you're using
*** remove the riving knife for plunge cuts, otherwise it can get in the way
|-
|-
| sawdust and small splinters can fly towards the operator and others ||  
| sawdust and small splinters can fly towards the operator and others ||  
* hook up a [[Shop Vac|shop vac]], but be aware the dust extraction from our "Herkules" saw is very incomplete
* hook up a [[Shop Vac|shop vac]], taking care that the hose can move freely when you push the saw
* wear [[goggles]]
* wear [[goggles]]
* [[Dust Mask|dust mask]]: depending on the material you're cutting
* [[Dust Mask|dust mask]]: depending on the material you're cutting
Line 41: Line 41:
'''Festool TS 75:'''
'''Festool TS 75:'''
* change cutting angle  
* change cutting angle  
* change and lock cutting depth
* change cutting depth
 
{{#set:
| checklist_title=Circular Saw
| checklist_symbols=M004
| checklist_symbols=M003
| checklist_symbols=M002
| checklist_symbols=M016
| checklist_link=https://wiki.comakingspace.de/index.php?title=Circular_Saw_Introduction
| checklist_before=**Must** check that path underneath the saw is clear (no table, floor, etc)
| checklist_before=**Should not** plunge into workpiece unless necessary (kickback)
| checklist_before=**Must** check blade height
| checklist_before=Think about your setup once the cut-off is removed (can it tip/fall?)
| checklist_during=**Must** make sure the rail can't slide
| checklist_after=Put Festool saw back into systainer and underneath the chop saw
}}




[[Category:Introductions]]
[[Category:Introductions]]

Latest revision as of 22:36, 11 January 2023

This is the content required for an introduction to our handheld circular saws - reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)

If you need this introduction, please reach out to the following tutors: Patrick, Lukas, Martin, Keno, Johannes, Luzian, Utis

Let's begin! First off, make sure you have read the machine's manual:

Safety

Personal protection: Protection - goggles.svg Protection - hearing.svg

(a dust mask could also be necessary depending on your material)

Dangers Precautions
sharp and rotating exposed blade - will keep spinning for a bit after turning the power off!
  • keep the saw secure after your cut until is has come to a complete stop
  • make sure the cutting path is free of obstacles (except your workpiece of course)
kickback: if the blade binds with the material it can push the saw back towards the user - this usually happens when the blade is pinched or the saw is started while already touching the wood (see video)
  • let the saw start before the blade touches the workpiece
  • plunge saw (Festool TS 75):
    • when doing a plunge cut, make sure the rail/workpiece can't move sideways. This could cause the blade to bind and kickback.
    • attach the endstop to the rail to reduce the chance of kickback
    • use an appropriately sized riving knife (DE: Spaltkeil) for the blade you're using
sawdust and small splinters can fly towards the operator and others
  • hook up a shop vac, taking care that the hose can move freely when you push the saw
  • wear goggles
  • dust mask: depending on the material you're cutting

Whenever you are cutting larger pieces, get a helper who can hold your cutoff so it doesn't fall down!

Demonstration

The tutor will show you these steps in detail:


Festool TS 75:

  • change cutting angle
  • change cutting depth
Retrieved from "https://wiki.comakingspace.de/index.php?title=Handheld_Circular_Saw_Introduction&oldid=13636"