Masonry Drill Bits: Difference between revisions
(available sizes, added photo) |
m (Location:: for SMW) |
||
| Line 6: | Line 6: | ||
|material=[[stone]], [[Material:Concrete|concrete]] | |material=[[stone]], [[Material:Concrete|concrete]] | ||
|used with=[[Impact Drill|impact drill]] ([[Shop Vac|shop vac]] to clean up) | |used with=[[Impact Drill|impact drill]] ([[Shop Vac|shop vac]] to clean up) | ||
|location=[[Drilling Table|drilling table]] | |location=[[Location::Drilling Table|drilling table]] | ||
|access= | |access=read this page | ||
}} | }} | ||
Masonry drill bits are not very sharp but possess a hard carbide chisel tip - therefore you need a [[Impact Drill|impact drill]] or a more powerful [[Rotary Hammer|rotary hammer]] to be successful in most cases. | Masonry drill bits are not very sharp but possess a hard carbide chisel tip - therefore you need a [[Impact Drill|impact drill]] or a more powerful [[Rotary Hammer|rotary hammer]] to be successful in most cases. | ||
| Line 24: | Line 24: | ||
|material=[[stone]], [[Material:Concrete|concrete]] | |material=[[stone]], [[Material:Concrete|concrete]] | ||
|used with=[[Rotary Hammer|rotary hammer]] ([[Shop Vac|shop vac]] to clean up) | |used with=[[Rotary Hammer|rotary hammer]] ([[Shop Vac|shop vac]] to clean up) | ||
|location=[[Drilling Table|drilling table]] | |location=[[Location::Drilling Table|drilling table]] | ||
|access= | |access=read this page | ||
}} | }} | ||
These special bits are not compatible with regular jawed drill chucks! They have grooves which allow them to move back and forth within an SDS chuck. | These special bits are not compatible with regular jawed drill chucks! They have grooves which allow them to move back and forth within an SDS chuck. | ||
Revision as of 22:15, 25 June 2019
| ToolInfoBox Masonry Drill Bits | |
|---|---|
| |
| Synonyms: | DE: Steinbohrer |
| Type: | bits |
| Material: | stone, concrete |
| Used with: | impact drill (shop vac to clean up) |
| Location: | drilling table |
| Access Requirements: | read this page |
Masonry drill bits are not very sharp but possess a hard carbide chisel tip - therefore you need a impact drill or a more powerful rotary hammer to be successful in most cases.
Once you're done drilling (make sure to wear personal protection against dust and stone chips!), you'll usually need wall anchors to secure anything in the hard substrate.
We can't just let everyone drill into the walls, but please don't hesitate to tell a manager if there is a spot that could really use a hole!
SDS Bits
| ToolInfoBox SDS Bits | |
|---|---|
| |
| Synonyms: | SDS shank bits, SDS drill bits, SDS chisel bits; DE: SDS-Bohrer, SDS-Meißel |
| Type: | bits |
| Material: | stone, concrete |
| Used with: | rotary hammer (shop vac to clean up) |
| Location: | drilling table |
| Access Requirements: | read this page |
These special bits are not compatible with regular jawed drill chucks! They have grooves which allow them to move back and forth within an SDS chuck.
Our rotary hammer has a chuck for "SDS-plus" drill bits or chisels.
Selection
We currently have the following SDS drill bits:
- 5 mm, short
- 6 mm, short
- 8 mm, short
- 6 mm, long
- 8 mm, long
- 10 mm, long
- 12 mm, long
In addition, we have three 250 mm chisel bits with a pointed tip, a 20 mm wide tip and a 40 mm wide tip.
