User:Lukas/Bench: Difference between revisions

From CoMakingSpace Wiki
("walls" Notiz übertragen)
No edit summary
Line 6: Line 6:
* backboard: 125{{x}}134{{x}}2 cm (H{{x}}B{{x}}T) plywood, needed to hold the shelves/distribute weight over the plasterboard wall
* backboard: 125{{x}}134{{x}}2 cm (H{{x}}B{{x}}T) plywood, needed to hold the shelves/distribute weight over the plasterboard wall
* sideboard: ?{{x}}?{{x}}? for hanging tools
* sideboard: ?{{x}}?{{x}}? for hanging tools
== Top ==
* laminated [https://www.bauhaus.info/bretter-dielen/glattkantbrett/p/20633945 douglas fir ''Glattkantbretter'']
** 300{{x}}14.5{{x}}1.8 cm boards cut in half two times (across & lengthwise) -> top approx. 150 cm wide and 7 cm thick
** not [[jointed]] as we didn't have the equipment yet - top [[plane]]d by hand after assembly
** a [[Biscuit Joiner|biscuit joiner]] would have helped with the glue-up - without it, some boards slipped
* 3 [[Sliding Dovetails|sliding dovetails]] (''Gratleisten'') to prevent warping, made of oak
== Understructure ==
* legs consist of three laminated douglas fir ''Glattkantbretter''
** final size: 14.5{{x}}?{{x}}? cm
* stretchers: need to be built next!
** at least something horizontal that will also hold a simple storage shelf
** perhaps also diagonal, depends on the stability achieved with the horizontals
== Planned Features ==
* [[Woodworking Vise|woodworking vise]] - on the right face, as tail vise? front should ideally be flush for planing
* 3/4" holes for [[holdfasts]] or [[Bench Dogs|bench dogs]]
** some in the top (one row in the woodworking vice's direction for sure), some in the legs
** exact layout TBD, can be drilled as the need becomes clear
* (sliding?) skirt with further dog holes to support large pieces that need planing on their edges
* horizontal twin screw ("Moxon") vise - non-permanent to leave room in the front?
* tool well? could fill gap on the back left (obstacle on the right that prevents the bench to be fully against the wall)
* leg vise on the right?
** would there be enough flush space left for planing?
** perhaps the vise could be screwed off whenever that much space is actually required
* plane stop on the far left
* storage options: just some "floor" for now
** perhaps (partial!) cabinet/drawers later
** or a second floor, with a cut-out to allow comfortable sitting at the bench?
== Further Inspiration/Research ==
* [https://www.youtube.com/watch?v=o7yF5av6MDM Stumpy Nubs' Roubo Workbench]
** similar top & leg lamination with mortises/tenons cut before the glue-up; I left out the threaded rods though (used them in my first [[Roubo Workbench]])
* Jay Bates' southern yellow pine workbench - only found ''after'' all the main decisions where made, but luckily in agreement with my wood choice:
** [https://www.youtube.com/watch?v=3HoOPhKMbms "Softwood Workbench VS Hardwood Workbench"]
** [https://www.youtube.com/watch?v=fg5qjed7u-k basic build video]
** [https://www.youtube.com/watch?v=x5tMPhHQYbA adding vises] - nice DIY leg & parallel vise (although with American hardware)
** [https://www.youtube.com/watch?v=H_cUOLwwx4c adding a storage cabinet]
** [https://www.youtube.com/watch?v=kexMm4JTa78 upgrades after some time of using it] (especially interesting part about the leg vise)
* [https://www.youtube.com/watch?v=PwLY-zbqA2g how to flatten a workbench top with handplanes]

Revision as of 17:18, 22 November 2018

"Private" page about my CoMaking bench - feel free to read on, but it's more of a note to myself than something I would expect to be interesting ;-)

The bench will be a Roubo style workbench and set up in the office. It will be made out of Douglas fir planks and end up about 1.5 m wide to fit into "my" corner.

Walls

  • backboard: 125 × 134 × 2 cm (H × B × T) plywood, needed to hold the shelves/distribute weight over the plasterboard wall
  • sideboard: ? × ? × ? for hanging tools

Top

  • laminated douglas fir Glattkantbretter
    • 300 × 14.5 × 1.8 cm boards cut in half two times (across & lengthwise) -> top approx. 150 cm wide and 7 cm thick
    • not jointed as we didn't have the equipment yet - top planed by hand after assembly
    • a biscuit joiner would have helped with the glue-up - without it, some boards slipped
  • 3 sliding dovetails (Gratleisten) to prevent warping, made of oak

Understructure

  • legs consist of three laminated douglas fir Glattkantbretter
    • final size: 14.5 × ? × ? cm
  • stretchers: need to be built next!
    • at least something horizontal that will also hold a simple storage shelf
    • perhaps also diagonal, depends on the stability achieved with the horizontals

Planned Features

  • woodworking vise - on the right face, as tail vise? front should ideally be flush for planing
  • 3/4" holes for holdfasts or bench dogs
    • some in the top (one row in the woodworking vice's direction for sure), some in the legs
    • exact layout TBD, can be drilled as the need becomes clear
  • (sliding?) skirt with further dog holes to support large pieces that need planing on their edges
  • horizontal twin screw ("Moxon") vise - non-permanent to leave room in the front?
  • tool well? could fill gap on the back left (obstacle on the right that prevents the bench to be fully against the wall)
  • leg vise on the right?
    • would there be enough flush space left for planing?
    • perhaps the vise could be screwed off whenever that much space is actually required
  • plane stop on the far left
  • storage options: just some "floor" for now
    • perhaps (partial!) cabinet/drawers later
    • or a second floor, with a cut-out to allow comfortable sitting at the bench?

Further Inspiration/Research

Retrieved from "https://wiki.comakingspace.de/index.php?title=User:Lukas/Bench&oldid=4858"