Search results

Sockets
==1/4" Square Drive Sockets== == 3/8" Square Drive Sockets ==

530 bytes (75 words) - 17:56, 29 May 2022
File:Materials-icon-square.png
remix of https://openclipart.org/detail/34807/wood-texture to obtain a square icon (edited using [[GIMP]])

(557 × 557 (106 KB)) - 15:51, 18 August 2017
File:Electronics-icon-square.png
remix of https://openclipart.org/detail/233406/pro-mini-pcb to obtain a square icon (edited using [[GIMP]])

(564 × 564 (138 KB)) - 15:50, 18 August 2017
File:Sockets.JPG
Some 3/8" square drive hex sockets for use with a [[Socket Wrench|socket wrench]]

(1,920 × 1,080 (326 KB)) - 22:17, 4 September 2017
File:Auger bit shaft - square.png
illustration of a square, tapered [[Auger Bit|auger bit]] shaft

(775 × 247 (56 KB)) - 21:48, 15 April 2020

simple [[Corner Clamping Jigs|corner clamping jigs]] made by cutting square boards in half and drilling two holes into each piece with a 35 mm [[Forstn

(1,920 × 1,080 (386 KB)) - 00:41, 15 November 2017

Braces
...square hole at its base for square tapered shafts [[File:auger bit shaft - square.png|80px]]

1 KB (166 words) - 17:35, 29 May 2022
File:VHS table 01.JPG
assembling four VHS tapes in a square with a [[Rivet Gun|rivet gun]] - this will be the base of a [[Project:VHS C

(1,920 × 1,080 (507 KB)) - 21:18, 27 September 2018
Hammer A3-31
You should check the fence for squareness against the table, e.g. with a [[square]] or [[inclinometer]]. Advanced users may also try to joint at other angles ...s are the opposite, you will still get a perfectly '''matching''', but not square, joint ([https://m.youtube.com/watch?v=C9scpxNqb40&t=1m12s video]).

4 KB (624 words) - 14:59, 29 August 2023
Corner Clamping Jigs
They are easy to make - just square up a board with the table saw and cut it in half, then drill holes for the

771 bytes (117 words) - 12:05, 2 May 2022
Bandsaw Direction Jig
|used with=[[square]], [[Bevel Gauge|bevel gauge]] or [[goniometer]]

1 KB (157 words) - 23:41, 11 May 2024
Woodturning Blanks
The diameter of these is often quite small and you'll get away with a square blank. === Cutting Square Blanks ===

5 KB (741 words) - 14:56, 23 November 2022
Bevel Gauges
|synonyms=false square; DE: Schmiege, Schrägmaß,<br>Winkelschmiege, Stellschmiege, "Winkelmesser

1 KB (152 words) - 00:59, 20 December 2023
Sheet Sanders
Sheet sanders have a square orbiting pad that lets you reach into corners and remove a similar amount o

1 KB (170 words) - 00:21, 25 October 2022
Levels
...reness of pieces against each other ''in two dimensions'', but a [[Squares|square]] is the proper tool for this kind of task.

1 KB (169 words) - 00:07, 19 February 2022
Pricking Awls
...ng holes than can securely be reamed by twisting the awl, you should use a square-tipped [[Birdcage Awl|birdcage awl]] instead!<sup> [http://www.inthewoodsho

1 KB (179 words) - 17:48, 29 May 2022
Project:Dining Room Table
* Square

1 KB (156 words) - 23:20, 22 September 2022
Sliding Table Saw Introduction
...ight and angle (if angle is changed: return to exactly 90° by means of a [[square]] or [[inclinometer]]!)

1 KB (201 words) - 13:13, 20 January 2024
Category:Bits
[[Sockets]] are bits that fit on the square pin of a [[Socket Wrench|socket wrench]].

13 members (0 subcategories, 0 files) - 16:15, 13 July 2018
Socket Wrenches
...other. Direction is changed by turning a lever or disc on the tool's head. Square drive [[sockets]] are required as "[[bits]]". Sockets are locked in place i

1 KB (199 words) - 17:56, 29 May 2022