Airbrush Area: Difference between revisions

Latest revision as of 18:51, 17 April 2024

This page is work in progress. We are aiming to open the new airbrush area in late April this year.

The airbrush area is located in the electronics room and contains our airbrushing related tools and machines. Not just for creating beautiful airbrush art, but also for painting 3D-printed models and other materials. Using an airbrush is easy, fun to learn – and a lot better for the environment than spray cans.

Airbrush Colors

Dedicated airbrush paints are usually water-based acrylic paints, with a milk-like consistency.

See Material:Airbrush Paint for more information and experiences!

Spray Booth and Air Extraction

Make sure you always have the spray booth's air extractor turned to on to "max Level" (Level 3) when the airbrush is in use (don't forget to use ear protection). The easiest method would be to keep the extractor running throughout your entire session, even if you take a break. That way, you don't forget to turn it on. Always keep the curtain behind you closed. Aerosols can travel for quite a long distance across the room, and we'd like to keep the other equipment free of paint. Once you've finished your session (whilst cleaning the airbrush): keep the air extractor running for a few more minutes and open the curtain and the door, to allow for additional air exchange in the room.

The spray booth we've built should be large enough to accomodate most needs, be it a A1-sized airbrush painting, or a t-shirt, shoes etc.

At the rear of the spray booth, you'll see a metal plate which can be tilted towards you, for a convenient viewing angle. For painting miniature figures / 3D-printed models etc: you'll find a turntable in one of the drawers. Also: Working with the airbrush is a lot more convenient if you lift your model up (to just below eye level). Positive side-effect: This also increases air ectraction efficiency.

Access

To use the machines in the airbrush area, you need to get an airbrush introduction.

@@ Line 1: / Line 1: @@
-{{Incomplete}}
+''This page is work in progress. We are aiming to open the new airbrush area in late April this year.''
-This page is work in progress. We are aiming to open the new airbrush area in February this year.
 The airbrush area is located in the [[Location::Electronics Room|electronics room]] and contains our [[airbrushing]] related tools and machines. Not just for creating beautiful airbrush art, but also for painting [[3DP|3D-printed]] models and other materials. Using an airbrush is easy, fun to learn – and a lot better for the environment than [[Spray Paint|spray cans]].
@@ Line 16: / Line 14: @@
 At the rear of the spray booth, you'll see a metal plate which can be tilted towards you, for a convenient viewing angle. For painting miniature figures / 3D-printed models etc: you'll find a turntable in one of the drawers. Also: Working with the airbrush is a lot more convenient if you lift your model up (to just below eye level). Positive side-effect: This also increases air ectraction efficiency.
-===Cleaning the airbrush===
-Cleaning is '''mandatory''' after every session. Even during a session, be aware that paint can dry quickly and clog the airbrush. If you interrupt your airbrush session even for as little as 5 Minutes: please remove any remaining paint AND rinse the airbrush with water and a few drops of cleaning agent, using the dedicated cleaning jar.
-At the end of the session (if no one else wants to continue using the airbrush corner): please clean the airbrush thoroughly, following these instructions: (This should take around 15 Minutes, so don't leave it too late.)
-*remove any remaining color from the compartment
-*fill the compartment with water and run it through the airbrush (Please use the rinsing jar for this, so to collect all coloured water and residue)
-*disconnect airbrush from compressor
-*disassemble the entire airbrush on a large enough and clean surface; make sure no parts fall down, particularly the needle (€15 replacement cost!) – see animated GIF below
-* clean all parts, removing ALL visible paint. Please do not use any metal brushes for cleaning.
-*reassemble the airbrush and put it back into its case – see animated GIF below
-====Animated GIFs that show the disassembly and reassembly of our Iwata Neo CN airbrush.====
-Airbrush disassembly (click image, then on the following page click "open in Media Viewer")
-[[File:Airbrush-Disassembly.gif|alt=Airbrush disassembly for cleaning|frameless]]
-Airbrush reassembly (click image, then on the following page click "open in Media Viewer")
-[[File:Airbrush-Assembly.gif|frameless]]
 == Access ==
-To use the airbrush area, you need to get an [[Airbrush Introduction|airbrush introduction]].
+To use the machines in the airbrush area, you need to get an [[Airbrush Introduction|airbrush introduction]].
 [[Category:Airbrushing]]
 [[Category:Facilities]]