|
|
| Line 1: |
Line 1: |
| This is the content required for an introduction to our [[Drill Press|drill press]] - '''reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
| | #REDIRECT [[Drill_Introduction]] |
| | |
| Let's begin! First off, make sure you have read the machine's [http://www.guede.com/sys/dl/55120_55190_55192_55193_55194_55195_55197_55423_55435_ml.pdf manual].
| |
| | |
| == Safety ==
| |
| [[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]] [[File:Protection - no gloves.svg|50px]]
| |
| | |
| (Breathing protection recommended depending on bit and material)
| |
| | |
| {| class="wikitable"
| |
| |-
| |
| ! Dangers !! Precautions
| |
| |-
| |
| | [[File:Danger_-_draw-in.svg|left|50px]] exposed & rapidly spinning chuck ||
| |
| * wear [[Personal Protection|personal protection]] but '''not''' [[gloves]], they could get caught!
| |
| * stay clear of the chuck when in operation - use a [[Machine Vise|machine vise]] for small workpieces
| |
| * make sure the drill press can't accidentally be turned on when changing a bit or touching the chuck for any other reason
| |
| * make sure there is nobody nearby who might be surprised by a piece of shrapnel flying their way!
| |
| |-
| |
| | possible kickback due to a [[Drill Bits|drill bit]] that binds with the material ||
| |
| * be prepared for sudden movements of the workpiece, especially when using large diameter drill bits or [[Hole Saw|hole saws]] - clamps can be very useful!
| |
| * never use a machine vise on top of a wooden board or two unsecured wooden boards at the same time (tower rule)!
| |
| |-
| |
| | the tool's table can destroy your drill bit || always check whether the tool movement you are planning is possible '''before''' turning it on
| |
| * adjust depth stop and/or table if necessary
| |
| * use a piece of [[Scrap Wood|scrap wood]] if the drill bit is too wide to fit through the hole in the table after exiting your workpiece
| |
| |-
| |
| | belt-based speed selection || unplug the drill press before opening the belt housing at the top
| |
| |-
| |
| | [[File:Danger_-_sudden_start.svg|left|50px]] no prevention of turning on after loss & restoration of power (''keine Anlaufsicherung'') || if the power has been lost for whatever reason, always press the "off" button before restoring it!
| |
| |-
| |
| | chuck key can be flung at you if left in the chuck when the drill is turned on || always remove the chuck key right after using it, do not leave it in the chuck any longer than necessary
| |
| |}
| |
| | |
| == Speed Selection ==
| |
| * '''unplug''' the drill press
| |
| * open the belt housing by removing the screw on the right
| |
| * check the explanation inside the top to see what speed is set/which belt setup you need for your desired speed
| |
| * loosen the screw holding the motor at distance
| |
| * pull the motor towards the front to loosen the belt
| |
| * repeat as necessary:
| |
| ** move the side of the belt that will go to a smaller pulley up or down (whichever you decided you'll need)
| |
| ** follow with the other side of the belt
| |
| * double-check you have the belt set up for the speed you wanted and that both sides are on pulleys at the same height
| |
| * push the motor back and tighten its screw again
| |
| * close the belt housing and put its screw back in
| |
| | |
| | |
| == Suggested Reading ==
| |
| Besides these safety notes, you should read about the different [[Drill Bits|drill bits]] to know what you're doing! '''Different materials usually require different bits, and the drilling speed depends on the bit as well as the type of material.'''
| |
| | |
| | |
| [[Category:Introductions]]
| |
