Talk:Router Table: Difference between revisions
From CoMakingSpace Wiki
NitramLegov (talk | contribs) No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
== Feed Direction == | == Feed Direction == | ||
My "only feed left to right" comment applies only to the (very common) setup with a fence and working on the outside of a workpiece, not to inside cuts - same as with the "different" proper feed directions for inside and outside cuts with a handheld router. We should probably illustrate this with a schematic rather than an easily misunderstood sentence... --[[User:Lukas|Lukas]] ([[User talk:Lukas|talk]]) 17:31, 20 September 2018 (CEST) | My "only feed left to right" comment applies only to the (very common) setup with a fence and working on the outside of a workpiece, not to inside cuts - same as with the "different" proper feed directions for inside and outside cuts with a handheld router. We should probably illustrate this with a schematic rather than an easily misunderstood sentence... --[[User:Lukas|Lukas]] ([[User talk:Lukas|talk]]) 17:31, 20 September 2018 (CEST) | ||
:: Schematic is schematized! Even with animation as this is really important... Any remaining questions? --[[User:Lukas|Lukas]] ([[User talk:Lukas|talk]]) 17:41, 23 October 2018 (CEST) | :: Schematic is schematized! Even with animation as this is really important... Any remaining questions? --[[User:Lukas|Lukas]] ([[User talk:Lukas|talk]]) 17:41, 23 October 2018 (CEST) | ||
:: yes, two points: 1. The animation does only show when you specifically open the gif due to the high resolution. Does it really need to be a high resolution gif? | |||
2. The animation only shows cutting on the inside of your workpiece. I understand that the principle is the same when cutting on the outside. However, I would propose a specific schematic for that. --[[User:NitramLegov|NitramLegov]] ([[User talk:NitramLegov|talk]]) 20:41, 23 October 2018 (CEST) | :::: yes, two points: | ||
::::1. The animation does only show when you specifically open the gif due to the high resolution. Does it really need to be a high resolution gif? | |||
::::2. The animation only shows cutting on the inside of your workpiece. I understand that the principle is the same when cutting on the outside. However, I would propose a specific schematic for that. --[[User:NitramLegov|NitramLegov]] ([[User talk:NitramLegov|talk]]) 20:41, 23 October 2018 (CEST) | |||
:::::: I'd say the animation is a bonus, I just had some time to kill and that's what came out...but I am planning to draw another schematic with a fence installed. Maybe the GIF can still be compressed (if a constant loop on the page is desirable)? --[[User:Lukas|Lukas]] ([[User talk:Lukas|talk]]) 22:20, 23 October 2018 (CEST) | |||
---- | ---- | ||
Revision as of 21:20, 23 October 2018
Feed Direction
My "only feed left to right" comment applies only to the (very common) setup with a fence and working on the outside of a workpiece, not to inside cuts - same as with the "different" proper feed directions for inside and outside cuts with a handheld router. We should probably illustrate this with a schematic rather than an easily misunderstood sentence... --Lukas (talk) 17:31, 20 September 2018 (CEST)
- yes, two points:
- 1. The animation does only show when you specifically open the gif due to the high resolution. Does it really need to be a high resolution gif?
- 2. The animation only shows cutting on the inside of your workpiece. I understand that the principle is the same when cutting on the outside. However, I would propose a specific schematic for that. --NitramLegov (talk) 20:41, 23 October 2018 (CEST)
